Emerson Fisher POSI-SEAL A31A Instruction Manual Download Page 12

Page: 12 / 28

Instruction Manual

D500242X012

A31A Cryogenic-Rotary Valve

February 2019

Figure 4. Available Seal Configurations

KEL‐F / ALUM SEAL

16B5083 / DOC

BODY

GRAPHITE
GASKET

RETAINING
RING

SEAL
RING

VALVE DISK

HIGH PRESSURE
AT SHUTOFF

BODY

GRAPHITE
GASKET

RETAINING
RING

SEAL
RING

VALVE DISK

HIGH PRESSURE
AT SHUTOFF

BODY

GRAPHITE
GASKET

RETAINING
RING

SEAL
RING

VALVE DISK

HIGH PRESSURE
AT SHUTOFF

NOVEX SEAL

KEL‐F SEAL

NOVEX Seal Installation

Unless otherwise indicated, key numbers and part names are listed in figures 7 and 8. Seal installation is shown in
figure 5.

A maintenance kit with installation tools is available through your

Emerson sales office

1. Locate the replacement seal ring (key 7) and note the shape of the ring. The ring is wider across one edge diameter

and narrower across the other edge diameter. Also, note the wide groove around the outside circumference.

Before installing the seal ring into the valve body, place the backup ring, if applicable, (key 8) into the wide, outer
groove of the seal ring.

2. Install the seal ring and backup ring assembly in the valve body. The wider outside diameter of the seal ring goes

into the T‐slot area of the valve body as shown in figure 5. Start the edge with the wider diameter into the T‐slot of
the valve body.

CAUTION

Use extreme care to avoid damaging the gasket while punching one initial screw hole through the gasket for alignment in
the following step.

Summary of Contents for Fisher POSI-SEAL A31A





























Search results

Summary of Contents for Fisher POSI-SEAL A31A

Reviews:

Related manuals for Fisher POSI-SEAL A31A

Brands by name

Popular brands

Emerson Fisher POSI-SEAL A31A, Instruction Manual

Search results

Summary of Contents for Fisher POSI-SEAL A31A

Reviews:

Related manuals for Fisher POSI-SEAL A31A

Brands by name

Popular brands