Emerson Fisher D3 Instruction Manual Download Page 18 | Manualshive

Page: 18 / 36

background image

Instruction Manual

D103460X012

D3 Valve with easy-Drive Actuator

October 2017

18

Figure 11. Packing and Belleville Spring Stacking Order

VALVE PLUG, BELLEVILLE SPRINGS, AND PACKING RETAINER CORRECTLY

INSTALLED AND TIGHTENED

BELLEVILLE SPRINGS FULLY ENCLOSED BY

THE PACKING RETAINER

PACKING RETAINER
(KEY 8)

UNTIGHTENED,
NOTE THE GAP

FULLY TIGHTENED,
NO GAP

Valve Plug and Seat Ring Maintenance

Trim Disassembly

Key numbers are referenced in figures 10, 12, and 13.

1. Isolate the control valve from the line pressure, release pressure from both sides of the valve body (key 1), and drain

the process media from both sides of the valve.

CAUTION

The following steps are intended to prevent damage to the valve plug (key 3) and seat ring (key 2) during the removal of the
bonnet and actuator.

For ON/OFF Actuators

2. Command the valve open.

3. Place an open end wrench or a similar obstruction about 6 mm (1/4 inch) thick under the FloPro.

4. Command the valve closed.

For Positioning Actuators

5. Command the valve to anywhere between 10% and 20% travel.

6. Isolate power and signal.

«
...
16
17
18
19
20
...
»

Summary of Contents for Fisher D3





































Reviews:

No comments

Related manuals for Fisher D3

Brand: Parasound Pages: 72

Brand: Jafar Pages: 15

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: Panasonic Pages: 45

Brand: Barthelme Pages: 8

Brand: CAB Pages: 28

Brand: C-TEC Pages: 16

Brand: C&T Solution Pages: 27

SECURIT ST800L+

Brand: C&K systems Pages: 16

Brand: FATEK Pages: 10

Brand: Racal Instruments Pages: 94

Brand: Racal Instruments Pages: 97

Brand: Jäger Pages: 50

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Brand: Nabco Pages: 35

1E0671-1 MCR2.9

Brand: Haberl Electronic Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands