manualshive.com logo in svg

Emerson Daniel 762, User Manual

Share
Download
Emerson Daniel 762 User Manual Download Page 102

Torque specification for socket-head screws

 (continued)

Table 9-2:   

Nominal pipe size

ANSI Class

Max Torque (ft-lb)

10" - 12"

600

17

WARNING!

OVER-TORQUING SCREWS HAZARD
The only function of the socket-head screws that secure the cylinder head to the cylinder is to
provide a mechanical joint between components during assembly or disassembly.

Do not Over torque the screws during assembly, see 

Table 9-2

.

9.4.2

Cylinder reassembly (2" - 12" valves with socket head

screws in circular pattern on cylinder head) B style

NOTICE

Lightly coat the O-rings with a high grade lubricant to ensure proper seal and assist in the
reassembly procedure. All O-rings should be inspected for nicks, cuts, distortion or other signs
of wear and be replaced as required.

Procedure

1.

Install check valve assembly, if removed.

2.

Return the O-rings to the cylinder head.

3.

Reinstall the O-ring (seat ring) and sealing ring (clockwise). Tighten locking set
screw (8).

4.

Reinstall the piston O-rings or Spring energized seals.

5.

Insert the piston in the cylinder followed by the spring.

6.

Assemble the cylinder and cylinder head, compressing the spring.

CAUTION!

CYLINDER RELEASE HAZARD

The cylinder assembly is now spring loaded and should be handled with extreme care.

Failure to comply may cause serious injury or damage to the equipment.

7.

Insert and tighten the cylinder socket head screws maintaining sufficient force to
hold the cylinder and the cylinder head together.

Planned maintenance

92

 Daniel Models 762, 763, 765, 766 and 767 Control Valves

Summary of Contents for Daniel 762





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands