Emerson COM Express Carrier Design Manual Download Page 46

Page: 46 / 103

Page 46 of 103

COM Express Carrier Type 2

Design

Guide

Table 11 LVDS Signals Description

8.1.1

Connector and Cable Considerations

When implementing LVDS signal pairs on a single-ended carrier board connector, the signals of a pair

should be arranged so that the positive and negative signals are side by side. The trace lengths of the

LVDS signal pairs between the COM Express module and the connector on the carrier board should be

the same as possible. Additionally, one or more ground traces/pins must be placed between the LVDS

pairs.

Balanced cables (twisted pair) are usually better than unbalanced cables (ribbon cable) for noise

reduction and signal quality. Balanced cables tend to generate less EMI due to field-canceling effects

and also tend to pick up electromagnetic radiation as common-mode noise, which is rejected by the

receiver.

Twisted pair cables provide a low-cost solution with good balance and flexibility. They are capable of
medium to long runs depending upon the application skew budget. A variety of shielding options are

available.

Ribbon cables are a cost effective and easy solution. Even though they are not well suited for high-

speed differential signaling, they do work fine for very short runs. Most cables will work effectively for

cable distances of less than 0.5 m.

The cables and connectors that are to be utilized should have a differential impedance of 100 ohms,

±15%. They should not introduce major impedance discontinuities that cause signal reflections. For

Summary of Contents for COM Express Carrier








































































































Search results

Summary of Contents for COM Express Carrier

Reviews:

Related manuals for COM Express Carrier

Brands by name

Popular brands

Emerson COM Express Carrier, Design Manual

Search results

Summary of Contents for COM Express Carrier

Reviews:

Related manuals for COM Express Carrier

Brands by name

Popular brands