background image

CEILING
COVER

HANGER BALL

PIN

SETSCREW

Figure 9

It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.

WARNING

!

12.

The fan comes with blue, black and white leads
that are 80” long. Before installing fan, measure
up approximately 6 to 9-inches above top of
hanger ball/downrod assembly. Cut off excess
leads and strip back insulation 1/2-inch from end
of leads.

13.

You have now completed the assembly of your
new ceiling fan. You can now proceed with
hanging and wiring your fan.

10.

Make sure the grommet is properly installed in
the coupling cover, then slide the coupling cover
on the downrod until it rests on the motor
housing. Place the ceiling cover over the
downrod. Be sure that the ceiling cover and the
coupling cover are both oriented correctly
(Figure 8).

6

It is critical that the clevis pin in the motor coupling
is properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.

WARNING

!

HAIRPIN
CLIP

CLEVIS
PIN

UPPER
SETSCREW

CLEVIS
PIN

SETSCREW

HAIRPIN
CLIP

MOTOR
COUPLING

SETSCREW

CLEVIS PIN

DOWNROD

MOTOR COUPLING

Figure 7

DOWNROD

CEILING
COVER

COUPLING COVER

Figure 8

NOTE: The setscrews must be properly installed
as described above, or fan wobble could result.

11.

Reinstall the hanger ball (Figure 9) on the
downrod as follows. Route the three 80” motor
leads through the hanger ball. Position the pin
through the two holes in the downrod and align
the hanger ball so the pin is captured in the
groove in the top of the hanger ball. Pull the
hanger ball up tight against the pin and securely
tighten the setscrew in the hanger ball. A loose
setscrew could create fan wobble.

Summary of Contents for BELLA CF452GES













Reviews: