Emerson AMS Installation Manual Download Page 53 | Manualshive

Page: 53 / 92

Emerson AMS Installation Manual Download Page 53

•

Connect terminal

A

of the 2-wire piezoelectric sensor to terminal

1

of the

CHARM Terminal Block.

•

Connect terminal

B

of the 2-wire piezoelectric sensor to terminal

2

of the

CHARM Terminal Block.

•

Connect the cable shield to a grounding terminal (see

5. Ensure that the cable gland, where the sensor cable is led through, is closed to keep

the IP protection class of the AMS Asset Monitor.

6. Continue with the installation or close the door (see

Close the AMS Asset Monitor

).

5.3

Install a DO 24 V DC High-Side CHARM

The DO 24 V DC High-Side CHARM is a discrete output CHARM for momentary output
signals or continuous pulse outputs. The CHARM is supplied by the AMS Asset Monitor. A
CHARM Terminal Block is required for the installation. If a relay output is required use the
CHARM Relay Output Terminal Block. See

Installing CHARMs hardware

for the general

CHARM installation procedure.

5.3.1

Connect the output signal wiring

Figure 5-8: Signal connection

A. Digital Output DO 24 V DC High-Side CHARM

B. CHARM Baseplate

C. CHARM Terminal Block

D. Field device with digital input

E. Cable shield connection

Installation Guide

Installing CHARMs hardware

MHM-97923-PBF

April 2020

MHM-97923-PBF, Rev. 1.0

53

«
...
51
52
53
54
55
...
»

Summary of Contents for AMS





























































































Reviews:

No comments