manualshive.com logo in svg

Emerson 01100017, Quick Start Manual

Share
Download
Emerson 01100017 Quick Start Manual Download Page 55

Unidrive M200-201 Quick Start Guide

55

Issue Number: 6

8.1      Alarm indications

In any mode, an alarm is an indication given on the display by alternating the alarm string with the 
drive status string display. If an action is not taken to eliminate any alarm except "tuning and LS" the 
drive may eventually trip. Alarms are not displayed when a parameter is being edited.

Table 8-2 Alarm indications

Alarm string

Description

br.res

Brake resistor overload. 

Braking Resistor Thermal Accumulator

 in the drive has 

reached 75.0 % of the value at which the drive will trip.Refer to the 

Drive User 

Guide

OV.Ld

Motor Protection Accumulator

 in the drive has reached 75.0 % of the value at 

which the drive will trip and the load on the drive is >100 %, reduce motor current 
(load). Refer to the 

Drive User Guide

d.OV.Ld

Drive over temperature. 

Percentage Of Drive Thermal Trip Level

 in the drive is 

greater than 90 %. Refer to the 

Drive User Guide

tuning

The autotune procedure has been initialized and an autotune in progress. 

LS

Limit switch active. Indicates that a limit switch is active and that is causing the 
motor to be stopped.

Lo.AC

Low voltage mode. See 

Low AC Alarm

 in 

Drive User Guide.

I.AC.Lt

Current limit active. See 

Current Limit Active

 in 

Drive User Guide.

Unidrive M200 201 Quick Start Guide English Iss6.book  Page 55  Thursday, September 10, 2015  1:48 PM

Summary of Contents for 01100017































































Reviews:

No comments

Brands by name

Popular brands

Load more brands