manualshive.com logo in svg

Emerson 01100017, Quick Start Manual

Share
Download
Emerson 01100017 Quick Start Manual Download Page 13

Unidrive M200-201 Quick Start Guide

13

Issue Number: 6

4.3.1     Use of residual current device (RCD)

There are three common types of ELCB / RCD:
1. AC - detects AC fault currents
2. A - detects AC and pulsating DC fault currents (provided the DC current reaches zero at least 

once every half cycle)

3. B - detects AC, pulsating DC and smooth DC fault currents 

•

Type AC should never be used with drives.

•

Type A can only be used with single phase drives

•

Type B must be used with three phase drives

If an external EMC filter is used, a delay of at least 50 ms should be incorporated to ensure spurious 
trips are not seen. The leakage current is likely to exceed the trip level if all of the phases are not 
energized simultaneously.

4.4      Control terminal configurations and wiring

* With Unidrive M201, the default is Pad (5). The setting of Pr 00.005 automatically sets the drive 
configuration.

Defaults are loaded before drive configuration changes are made. 
Action will only occur if the drive is inactive, not in UU state and no User Actions are running. 

Only type B ELCB / RCD are suitable for use with 3 phase inverter drives. 

00.005

Drive Configuration

RW

Txt

PT

US

OL

Ú

AV (0), AI (1), AV.Pr (2), AI.Pr (3), 

Preset (4), Pad (5), Pad.Ref (6), 

E.Pot (7), torque (8), Pid (9)

Ö

AV (0)*

RFC-A

Value

Text

Description

0

AV

Analog input 1 (voltage) Analog input 2 (voltage) selected by terminal 
(Local/Remote)

1

AI

Analog input 1 (current) or Analog input 2 (voltage) selected by terminal 
(Local/Remote)

2

AV.Pr

Analog input 1 (voltage) or 3 presets selected by terminal

3

AI.Pr

Analog input 1 (current) or 3 presets selected by terminal

4

Preset

Four presets selected by terminal

5

Pad

Keypad reference

6

Pad.Ref Keypad reference with terminal control

7

E.Pot

Electronic Potentiometer

8

torque

Torque mode, Analog input 1 (current frequency reference) or Analog input 2 
(voltage torque reference) selected by terminal

9

Pid

PID mode, Analog input 1 (current feedback source) and Analog input 2 
(voltage reference source)

WARNING

Unidrive M200 201 Quick Start Guide English Iss6.book  Page 13  Thursday, September 10, 2015  1:48 PM

Summary of Contents for 01100017































































Reviews:

No comments

Brands by name

Popular brands

Load more brands