manualshive.com logo in svg

EMC2 VNXe3150, Hardware Information Manual

Share
Download
EMC2 VNXe3150 Hardware Information Manual Download Page 44

42

EMC VNXe3150 Hardware Information Guide

Overview

Figure 28  Example of a DAE AC power supply/cooling module power in (recessed) connector (plug) 
and status LEDs

Table 20

 describes the DAE power supply/cooling module LEDs.

The power supply/cooling modules are located above the LCCs. The units integrate 
independent power supply and blower cooling assemblies into a single module.

Each power supply is an auto-ranging, power-factor-corrected, multi-output, offline 
converter with its own line cord. Each supply supports a fully configured DAE and shares 
load currents with the other supply. The drives and LCCs have individual soft-start 
switches that protect the disk drives and LCCs if they are installed while the disk enclosure 
is powered up.

Note: Each line cord should be plugged into a different AC power distribution system 
(PDU) for high availability (the 

VNXe3150 Installation Guide

 provides more information).

DAE LCC input/output ports and connectors

The 2U, 12 (3.5-inch) DAE LCC supports two 6-Gb/s SAS x 4 ports on the rear of the device.

6-Gb/s SAS x4 ports —

The 2U, DAE LCC supports two 6-Gb/s SAS x4 ports (labeled 6GB 

SAS x4) on the rear of each LCC (A and B). This port is a 26-circuit SAS small form-factor 
8088 (SFF-8088) specification connector (socket or receptacle) using an SFF-8088 
specification mini-SAS 26-circuit cable (plug) with a pull tab.

1

Fan fault LED

Power supply in

Power on LED

Fault LED

VNX-000083

Table 20  DAE AC power supply/cooling module LEDs

LED

Color

State

Description

Power

Green

On

Power on

—

Off

Power  off

Power fault

Amber

On

Power supply fault, check cable connection

Blinking

BIOS, POST and OS booting up or system 

overheating

—

Off

No fault or power off

Fan fault

Amber

Fault

Fault, not operating normally

—

No fault

No fault, fan operating normally

Summary of Contents for VNXe3150

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands