EMC2 VNXe3150 Hardware Information Manual Download Page 7 | Manualshive

Page: 7 / 56

EMC2 VNXe3150 Hardware Information Manual Download Page 7

EMC VNXe3150 Hardware Information Guide

7

Preface

How this document is organized

The major sections of this guide are listed in the following table.

Audience

This document provides an overview of the architecture, features, and components of the
VNXe3150 platform. The specific aspects of the VNXe3150 platform and its major
components include the front and rear LED indicators and the connectors on the DPE and
the DAE.

Related documentation

The following EMC publication provides additional information:

◆

EMC VNXe3150 System Installation Guide

This guide is available online at

www.emc.com/vnxesupport.

On this page, click

Documentation. On the page that appears, under VNXe Series, click VNXe3150. On the
next page that appears, under Content type, click Manuals and Guides. On the right side
of the page that appears, a list of all the VNXe3150 product guides will appear. Select the
guide you are interested in from this list.

Conventions used in this document

EMC uses the following conventions for special notices:

DANGER indicates a hazardous situation which, if not avoided, will result in death or
serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or
serious injury.

Title

Description

“Overview” on page 9

Describes the software and hardware features of a typical

VNXe3150.

“VNXe3150 platform” on

Describes and shows the front and rear views of a typical

VNXe3150.

“System component

description” on page 13

Provides a description of the components that comprise a

VNXe3150. Along with a description, illustrations of each

component are also shown.

“Disk processor enclosure” on

Describes and illustrates the front and rear of a DPE and the

components that comprise the DPE.

“Cache Protection Module” on

Describes and illustrates the Cache Protection Module.

“Disk-array enclosure” on

Describes and illustrates the two types of DAEs available for the

VNXe3150.

«
...
5
6
7
8
9
...
»

Summary of Contents for VNXe3150

























































Reviews:

No comments