manualshive.com logo in svg

EMC2 VNXe3150, Hardware Information Manual, Page: 21 / 56

Share
Download
EMC2 VNXe3150 Hardware Information Manual Download Page 21

System component description

19

Overview

DPE

On the rear of the 2U DPE, viewing from left to right, each 2U DPE consists of the following 
connectors, status LEDs, latch handles, and so on:

◆

AC power supply module:

• Power in (recessed) connector (plug)

• Power supply status LEDs (power on and fault)

• Power supply latch handle

◆

SP B and A:

• USB

• Two 1-GbE iSCSI (host IP connect) ports

• Two 6-Gb/s SAS x4 ports (labeled 6Gb SAS 0 x4 and 1 x4)

Note: 6Gb SAS port 1 x4 is not used at this time.

• Either a four-port 1-Gb/s copper Ethernet I/O personality module or two-port 

10-Gb/s copper Ethernet I/O personality module

Note: The two-port 10-Gb/s copper Ethernet I/O personality module is not 
supported in a single SP configuration.

• Two (RJ-45) LAN connectors (labeled with a network management symbol and a 

wrench symbol)

Note: The RJ-45 LAN connector with a wrench symbol is not used at this time.

• Two (micro DB-9) RS-232/EIA connectors (labeled with a battery symbol and a 

wrench symbol)

Note: The DB-9 connector with a battery symbol is not used at this time.

• SP  status  LEDs

• RS-232/EIA

• SP latch handles (top of SP left and right)

Figure 10 on page 20

 shows the location of the SP components.

Summary of Contents for VNXe3150

























































Reviews:

No comments