EMC2 AX100 Series Manual Download Page 29 | Manualshive

Page: 29 / 68

background image

AX100-Series - Installing a Fibre Channel Storage System with a Direct Connection to a NetWare Server

29

Connecting ac Power to an AX100SC Storage System

Connecting ac Power to an AX100SC Storage System

Read this section if you are connecting power to anAX100SC
(single-SP) storage system. If you are connecting power to anAX100
(dual-SP) storage system, go to

Connecting ac Power to an AX100

Storage System

Before You Start

To complete this procedure, you need the ac power cables
appropriate to your power source. These cables shipped with the
storage system.

Connect ac Power to the AX100SC Storage System

CAUTION

!

Do not connect the power cord to an ac power source until the
storage system is installed in the cabinet. The storage system
powers up as soon as it is connected to an ac source.

As you perform the procedure below, refer to Figure 11.

1. Plug a storage-system power cord into the power connector on

the power supply in the storage system.

2. Secure the power cord with the retention bail at the connector.

The retention bail prevents the power cord from pulling out of the
connector and causing the storage system to power down
unexpectedly.

3. Plug the storage-system power cord into the ac power source in

the cabinet (power distribution unit) or other source.

«
...
27
28
29
30
31
...
»

Summary of Contents for AX100 Series





































































Reviews:

No comments

Related manuals for AX100 Series

DCDC SBC Series

Brand: Infineon Pages: 17

Brand: Meccanica Fadini Pages: 4

Brand: Linear Technology Pages: 10

790XT-G35 series

Brand: MSI Pages: 103

Brand: Advantech Pages: 116

Brand: OLIMEX Pages: 26

SBC81870 Series

Brand: AXIOMTEK Pages: 120

Brand: Atmel Pages: 59

CS631-C246/Q370

Brand: DFI Pages: 79

Brand: BCM Pages: 57

Brand: IDT Pages: 18

Brand: Analog Devices Pages: 8

Brand: Supermicro Pages: 88

Brand: Texas Instruments Pages: 21

CC85-CC2590EM Series

Brand: Texas Instruments Pages: 7

Brand: A-Trend Pages: 49

Brand: Gan Systems Pages: 22

Brand: Microchip Technology Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands