Fast Start-up, Safely Operate
and Efficiently Clean!
Installation and Operation Manual
1. Preparation of Your Pool
Before assembling and installing your cleaner, your pool should be
clean and algae-free so as not to inhibit the cleaner's traction. If
necessary, make the following preparations before proceeding:
1) Chemically balance the pool water.
2) Brush pool and let the debris settle.
3) Hand vacuum thoroughly.
4) Clean filter and pump strainer basket.
II. Assembly
Remove the body and all of its parts from the box and check to
make sure that all components are included. Refer to Figure 1.
Components Check List
A) Body
B) Nut
C) Hose weight
D) Automatic regulator valve
E) 1.5" & 2 " Hose Cone
F) Roller bumper strap
G) Pleated Disc
H) Hose-10.4m total length (not shown)
I) Interleaver
Step
1) Attach The disc
To install the disc, locate the words
"Up"
and face them towards the
main body, slip the disc over the Interleaver-(flat side down towards
pool floor)-and full gently until it seats itself on the other side in its
groove as illustrated in Figure
2) disc must be installed flat side down, pleated side up.
Once in
place, the disc should rotate and turn freely.
The disc is not reversible.
The raised pleats on the Pleated Disc must
face upward. The flat side of the disc should face down to rest
against the pool surface.
Step 2. Attach The Roller Bumper Strap
Insert the bottom end of the strap into the slot provided on the main
body. Insert the top end of the strap into the locking clip attached to
the swivel head. See Figure 3.
Step 3. Assemble The Hose
Your fully assembled the cleaner should look like this.
III. Installation
The cleaner is designed to work in a wide variety of swimming pools.
Twist and push the female ends onto the male ends after dipping the
This is the reason certain items (such as a 2" hose cone and valve
ends into the pool to wet them. See Figure 4. Continue until you've
cap for the automatic regulator valve) are included with your
connected all the sections you need. After connecting the hose
cleaner. These may or may not be needed, depending on the
weights to the hose as described in "Table A", then connect the hose
particular features of your pool.
to the cleaner. See Figure 5.
Both the standard in-skimmer installation and an optional vacuum
line installation are covered in this manual. Check to see which most
One of the hose sections has 2 female ends and a hose protector.
closely fits your pool configuration and follow the directions.
This section should be fitted last and attached to the pool's vacuum
connection.
Figure 2
Main body
Pleated Disc
in groove
Pleats of
Pleated Disc
Figure 1
A
B
C
D
E
F
G
H
I
X12
X1
Figure 5
Male connection of
the top assembly
should connect to
the female end
of the hose
Female / female section to be
added last, to the Automatic
Valve Regulator
Figure 4
Male hose end
Female hose end
Female hose
Automatic Regulator Valve
Figure 3
Locking
Parts list
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CE306A
CE306B
CE306C
X12
X1
15
16
Key NO.
Part NO.
Product Description
QTY
1
89050301
Hose weight
1
2
01112017
Nut
1
3
01100005
Roller bumper strap
1
4
89050302
Top Assembly for Tube
1
5
01010015
Tube
2
6
89050303
Body with Screws
1
7
08050017
Automatic Regulator Valve
1
8
02141005
Flexi Hose Connector
1
9
02140001
2" Hose Cone
1
10
89050304
Bottom Assembly for Tube
1
11
02300002
Flipper
1
12
01112018
Flipper Cover
1
13
02300003
Pleated Disc
1
14
02300001
Interleaver
1
15
01093008
Hose (Male - Female)
12
16
01093009
Hose (Female - Female)
1
4
1
EMCE15040757
