manualshive.com logo in svg

ELZAB CAT 27 NEPTUN 2, User Manual, Page: 14 / 32

Share
Download
ELZAB CAT 27 NEPTUN 2 User Manual Download Page 14

ELZAB S.A. 

 

User Manual CAT 27 scales series 

13 

 

5.

 

Configuration of the scale 

To operate the menu of the scale there are used all three keys of the scale. Their functions are as 
follows: 

Key 

Meaning 

Key 

Meaning 

 

previous menu item 

 

selection of the menu 

item 

 

next menu item 

+

 

 

exit from menu 

 

5.1.

 

Main menu 

Structure of the scale’s main menu: 

 

MAIN MENU 

Entrance to the menu: press and hold for 2 seconds the 

 

key.

 

01  USER MENU 

02  SERVICE MENU 

03  RESET SCALE 

04  EXIT FROM MENU 

 

01 

–  USER MENU 

The  menu  contains  functions  useful  during  the  installation  and 
operation  of  the  scale  concerning  among  others  the  transmission 
parameters, configuration of measuring features

 

and the display. 

02 

–  SERVICE MENU 

The menu  is  designed for  qualified  scale servicemen. The service 
menu is described in detail in the Service Manual for the CAT 27 
scales series. 

03 

–  RESET SCALE 

This  function  enables  to  reset  the  scale  without  turning  off  the 
power. 

04 

–  EXIT FROM MENU 

Exit from the menu to the weighing mode. 

 

Summary of Contents for CAT 27 NEPTUN 2

































Reviews:

No comments