background image

  WEP-2L. User manual

58

6.5.4  Setting the date and time

Commands to configure NTP server time synchronization

WEP-2L(root):/# 

configure

WEP-2L(config):/# 

date-time

WEP-2L(config):/date-time# 

mode

 

ntp 

(Enable NTP operation mode)

 

WEP-2L(config):/date-time#

 ntp

WEP-2L(config):/date-time/ntp# 

server <NTP server IP address> 

(NTP server configuration)

 

WEP-2L(config):/date-time/ntp# 

exit

WEP-2L(config):/date-time# 

common

WEP-2L(config):/date-time/common# 

timezone 'Asia/Novosibirsk (Novosibirsk)'

 

(Timezone configuration)

 

WEP-2L(config):/date-time/common#

 save

6.6  APB service configuration

The APB service is used to provide portal roaming of clients between access points connected to the service. 

Commands for APB service configuration

WEP-2L(root):/# 

 

configure

 

WEP-2L(config):/# 

 

captive-portal

 

WEP-2L(config):/captive-portal# 

 

apbd 

 

WEP-2L(config):/captive-portal/apbd# 

 

roam_service_url <

APB service 

address

>

 

(Example: roam_service_url 

ws://192.168.1.100:8090/apb/broadcast

 )

 

WEP-2L(config):/captive-portal/apbd# 

 

enabled

 

true 

 

(Enabling APB service. To disable it, enter

 

false

)

 

WEP-2L(config):captive-portal/apbd# 

 

save

Summary of Contents for WEP-2L


































































Reviews: