ELTEX WEP-2L User Manual Download Page 10

Page: 10 / 65

WEP-2L. User manual

•
•
•
•
•

2.5 Light indication

The current device state is displayed by

Wi-Fi

LAN, Power

indicators. The list of indicators’ possible states is

given below.

Table 3 – Light indication of device state

LED

LED status

Device state

Wi-Fi

solid green

the Wi-Fi network is active

flashing green

the process of data transmission trough a

wireless network

LAN

solid green (10, 100 Mbps)/ solid orange (1000 Mbps)

the link with the connected network device is
established

flashing green

the process of packet data transmission
through LAN interface

Power
(on the
device
top panel)

solid green

the device power on, normal operation

solid orange

the device is loaded but IP address is not
received via DHCP

solid red

the device is loading

2.6 Reset to the default settings

In order to reset the device to factory settings, press and hold the «F» button until «Power» indicator starts
flashing. Device will be rebooted automatically. DHCP client will be launched by default. If the address is not

obtained via DHCP, the device will have the default IP address —

192.168.1.10

, and the following netmask

—

255.255.255.0

2.7 Delivery package

The delivery package includes:

WEP-2L wireless access point;
Mounting kit;
Operating manual (supplied on a CD);
Conformity certificate;
Technical passport.

Summary of Contents for WEP-2L


































































Search results

Summary of Contents for WEP-2L

Reviews:

Related manuals for WEP-2L

Brands by name

Popular brands

ELTEX WEP-2L, User Manual

Search results

Summary of Contents for WEP-2L

Reviews:

Related manuals for WEP-2L

Brands by name

Popular brands