manualshive.com logo in svg

ELTEX TAU-4.IP, Operation Manual, Page: 29 / 190

Share
Download
ELTEX TAU-4.IP Operation Manual Download Page 29

 

29

 

VoIP Subscriber Gateways 

 

2.1.5 The ‘Upgrade’ submenu 

Use the submenu to update the device control program.  

 

-

 

Firmware  image to  upload:

  –  firmware  file  selection  –  you should  select  *.tgz. archive 

file. 

Select firmware file and click 

‘Upgrade’ button to upgrade firmware of the device. 

The process of 

upgrading a firmware can take a few minutes, after that the device will automatically reboot.  

 

Do not switch off or reboot the device during the software update.  

 

When  return  to  firmware  version  2.4.2  and  later,  reset  the  device  to  the  default 
configuration for the device proper operation.  

 

2.2 The ‘Network’ menu 

Use  the 

‘Network’

  menu  to  configure  VLAN,  WAN  interface,  SNMP  client  and  wireless  Wi-Fi 

access point;   install МАС-addresses, NAT rules (for the device with Wi-Fi module) and operate with 
routing table. 

2.2.1 The ‘Network settings’ submenu 

Use  the  menu  to  specify  the  network  interface  configuration  and  configure  the  access  to  the 

device via various protocols.   

To connect the device to the provider’s network, you should to check the network settings with 

operator. When static settings are used, in the field 

‘Protocol for address getting on WAN’

 you should 

select 

‘Static’

  value  and  full 

‘WAN  IP  Address’,  ‘WAN  subnet  mask’,  ‘1st  DNS’,  ‘2nd  DNS’

  and 

‘The 

default  gateway’

  fields  by  values  received  from  providers.  If  the  devices  on  the  provider  network 

receive  network  settings  via  DHCP,  PPPoE,  L2TP  or  PPTP  protocol,  you  should  select  corresponding 
protocols  from 

‘Protocol  for  address  getting  on  WAN’

  box  and  use  provider  instructions  for  correct 

device configuration. 

Network model is based on the service connections. You can configure maximum three services: 

Internet,  VoIP

  and 

Management

.  Their  division  is  implemented  by  VLAN  identifiers.  By  default,  key 

service 

(Internet)

 is set up, and other services are disabled.  

Summary of Contents for TAU-4.IP































































































































































































Reviews:

No comments