manualshive.com logo in svg

ELTEX TAU-36.IP, Operation Manual

Share
Download
ELTEX TAU-36.IP Operation Manual Download Page 95

_________________________________________________________________________________ 

 

_________________________________________________________________________________ 

TAU-72.IP/TAU-36.IP Universal Network Terminal                                            95 

5.1.2.5

 

Simultaneous Call Limits (Call limits) 

In 

'Call limits'

 submenu, you may configure simultaneous call limits for the communicating host. 

 

–

 

Host of neighbour gateway

—

hostname of a communicating gateway. To limit the calls via SIP-proxy or 

H323 Gatekeeper, select the 

'proxy/gk'

 checkbox (defines the total call limit through all proxies and from 

all profiles); to enter host address, select 

'host'

.  

–

 

Simultaneous calls count

—

maximum number of simultaneous (incoming and outgoing) calls. 

To discard all changes made to configuration, click 

'Undo All Changes'

  button. To store changes to non-

volatile memory of the device, click 

'Save'

 button.

 

5.1.2.6

 

Configuration of Supplementary Service Codes (Suppl. Service Codes) 

Supplementary  services  are  provided  to  each  subscriber,  but  in  order  to  use  a  specific  service,  the 

subscriber  must  enable  it  first  at  the  service  provider.  Service  providers  may  create  their  own  service  plans 
containing  several  supplementary  services.  To  do  this,  in 

5.1.2.4

  section,  on 

Suppl.  Service

 

 

tab,  select  the 

checkboxes against the desired supplementary services. 

Subscribers may manage state of services from their phone units. The following features are available: 

–

 

Service activation—activation and additional data input. 

–

 

Service verification. 

–

 

Service cancellation—deactivation of a service. 

When  the  activation  code  is  entered  or  the  service  is  cancelled,  subscribers  may  hear  either  a 

'confirmation' tone (3 short tones), or a 'busy' tone (intermittent tone with tone/pause duration—0.35/0.35s.) 
'Confirmation' tone means that the service has been activated or cancelled successfully, 'busy' tone—that this 
service is not enabled for this subscriber. 

After service confirmation code entry, the subscriber may hear either 'PBX response' tone (continuous) or 

a  'busy'  tone.  'PBX  response'  tone  means  that the  service  has  been  enabled  and  activated  for  the  subscriber, 
'busy' tone—that this service is not enabled for the subscriber. 

Summary of Contents for TAU-36.IP














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands