manualshive.com logo in svg

ELTEX TAU-36.IP, Operation Manual, Page: 56 / 205

Share
Download
ELTEX TAU-36.IP Operation Manual Download Page 56

_________________________________________________________________________________ 

_________________________________________________________________________________ 

56                                           TAU-72.IP/TAU-36.IP Universal Network Terminal 

61:63:73—suboption value (acs). 
04—Password suboption value. 
06—length, 6bytes. 
61:63:73:61:63:73—suboption value (acsacs). 

5.1.2

 

VoIP Configuration

 (

PBX)

 

In 'PBX' menu, you can configure VoIP (Voice over IP): SIP/H.323 protocol configuration, Quality of Service 

configuration, FXS interface configuration, installation of codecs, numbering schedule, etc. 

5.1.2.1

 

Basic Configuration (Main)

 

In 

'Basic Configuration' ('Main')

  submenu, you can configure  basic  device settings: set  the  device name, 

device prefix, and global timers. 

 

General configuration: 

–

 

Device  name

—name  of  the  device.  Used  for  sending  messages  to  SYSLOG  server,  enables  device 

identification. 

–

 

Use prefix (SIP-T)

—when checked, 

Prefix (SIP-T)

 parameter value will be used as a PBX prefix. This prefix 

will  be  added  before  the  subscriber's  number  and  will  affect  the  number  type:  if  the  prefix  is  present, 

subscriber's  number  will  be  'national';  if  it  is  absent,  then  the  number  will  be  'subscriber'  (passed  in  CgPN 

parameter). 

–

 

Prefix (SIP-T)

—PBX prefix (numeric string).  

 

Use  prefix  (SIP-T) 

and

  Prefix  (SIP-T) 

parameters  are  used  only  in  gateway  operation  via  SIP-T 

protocol.  SIP-T  protocol  operation  mode  is  defined  by:  in  incoming  communications

—

the 

presence of ISUP attachment in initializing SIP INVITE request, in outgoing communications

—

SIP-T 

protocol configuration in routing prefix (see Section 5.1.2.2.5). 

—

 

Start timer

—dialling timeout for the first digit of a number; when there is no dialling during the specified 

time, 'busy' tone will be sent to the subscriber, and the dialling will end. 

–

 

Duration timer

—complete number dialling timeout. Takes effect after the first digit of a number has 

been dialled, and specifies the time for dialling the full number. 

Summary of Contents for TAU-36.IP














































































































































































































Reviews:

No comments