manualshive.com logo in svg

ELTEX TAU-32M.IP, Operation Manual, Page: 82 / 334

Share
Download
ELTEX TAU-32M.IP Operation Manual Download Page 82

_________________________________________________________________________________ 

 _________________________________________________________________________________ 

82        

                    Universal Network Terminal TAU-32M.IP 

<proto> 

–

 protocol (FTP, TFTP, HTTP, HTTPS),  

<address>–autoupdate server IP address or domain name,  
<port>–autoupdate server port (optional parameter); 

–

 

6–autoupdate configuration file name; 

–

 

7—autoupdate firmware file name. 

Upon receiving Option 43, suboption 1, device launches management via TR-069 protocol. 

Example of the option record: 

01:10:68:74:74:70:3A:2F:2F:61:63:73:2E:72:75:3A:38:30:02:02:31:39:03:03:61:63:73:04:06:61:63:73
:61:63:73 

where: 

01 – 

ACS URL

 suboption number;                                  

10–length, 16bytes (0х10 = 16 dec); 
68:74:74:70:3A:2F:2F:61:63:73:2E:72:75:3A:38:30–suboption value (http://acs.ru:80); 
02 – 

Provisioning code

 suboption number; 

02 – length, 2bytes; 
31:39 – suboption value (19); 
03 – Login suboption value; 
03 – length, 3bytes; 
61:63:73 – suboption value (acs); 
04 – Password suboption value; 
06 – length, 6 bytes; 
61:63:73:61:63:73 – suboption value (acsacs). 

5.1.2

 

The 'PBX' menu. VoIP configuration 

In  the 

'PBX'

  menu,  you  can  configure  VoIP  (Voice  over  IP):  SIP/H.323  protocol  configuration,  TCP/IP 

configuration, FXS interface configuration, installation of codecs, numbering schedule, etc. 

5.1.2.1

 

The 'Main' submenu. 

In the

('Main') 

submenu, you can configure basic device settings: set the device name, device prefix, and global 

timers. 

 

For rev.B: 

 

Summary of Contents for TAU-32M.IP















































































































































































































































































































































Reviews:

No comments