manualshive.com logo in svg

ELTEX TAU-32M.IP, Operation Manual, Page: 74 / 334

Share
Download
ELTEX TAU-32M.IP Operation Manual Download Page 74

_________________________________________________________________________________ 

 _________________________________________________________________________________ 

74        

                    Universal Network Terminal TAU-32M.IP 

fxs72updateFwOk 

INFO 

Firmware is updated 

1.3.6.1.4.1.35265.3.7.20 

 

fxs72BpuAlarmTrap 

CRITICAL 

No connection with BPU  1.3.6.1.4.1.35265.3.6.12 

 

fxs72BpuOkTrap 

CLEAR 

BPU connection restored  1.3.6.1.4.1.35265.3.7.12 

 

5.1.1.7

 

The 'Syslog' submenu. Syslog Protocol Configuration 

In the 

'Syslog'

 menu, you may configure system log settings.  

SYSLOG

  is  a  protocol,  designed  for  transmission  of  messages  on  current  system  events.  Gateway  software 

generates system data logs on operation of system applications and signalling protocols, as well as occurred failures 
and sends them to SYSLOG server. 

 

Syslog configuration: 

–

 

Run syslog on startup–

when checked, run Syslog on device startup;

 

–

 

Syslog to file

–when checked, save Syslog into file to view it later via web interface;

 

–

 

Syslog server–

Syslog

 server

 IP address;

 

 

High debugging levels can lead to delays in the operation of the device.  
It is NOT RECOMMENDED without having to use a syslog. 

 

System log should be used only when problems in gateway operation occur, and you have to 
identify the reason. To define the necessary debug levels, consult ELTEX Service Centre Specialist. 

Summary of Contents for TAU-32M.IP















































































































































































































































































































































Reviews:

No comments