ELTEX MA4000-PX Operation And Maintenance Manual Download Page 81 | Manualshive

Page: 81 / 181

background image

User Manual, Part III 81

Subscriber access/aggregation node МA4000-РХ

24.4

DHCPv6 Relay Agent profiles management

DHCPv6 Relay Agent configuration is performed via profiles system. By default, dhcp-ra-00 profile

is used for all VLANs.

The flexibility of configuration provides opportunity to assign DHCPv6 profiles not only for

MA4000 slot, but for specified VLAN individually. The assignment is implemented in several steps.

Step 1. Assign a profile by default using

slot <id> profile dhcpv6-ra

command for all VLANs:

ma4000# configure terminal
ma4000(config)# slot 0 profile dhcpv6-ra dhcpv6-ra-00

Step 2. If necessary, create new

DHCPv6 Relay Agent

profile by using

profile dhcpv6-ra

command.

As a parameter, define profile's name:

ma4000(config)# profile dhcpv6-ra dhcpv6-ra-01
ma4000(config-dhcpv6-ra)("dhcpv6-ra-01")# exit

Step 3. If necessary, assign the created profile on selected VLAN, using

slot <id> profile dhcpv6-ra

command. As parameters, define profile's name and VLAN ID:

ma4000(config)# slot 0 profile dhcpv6-ra dhcpv6-ra-01 vlan 100

Step 4. Check the changes by

show slot <id> gpon olt configuration

command.

ma4000# show slot 1 gpon olt configuration
  Profile pppoe-ia:                              pppoe-ia-00       OLT
Profile PPPoE Intermediate Agent 0
  Profile dhcp-ra:                               dhcp-ra-00        OLT
Profile DHCP Relay Agent 0
  Profile dhcp-ra per VLAN: <list is empty>
  Profile dhcpv6-ra per VLAN: <list is empty>
  Profile dhcpv6-ra:                               dhcpv6-ra-00   OLT
Profile DHCPv6 Relay Agent 0

Step 5. Apply the changes, using

commit

command:

ma4000(config)# do commit

24.5

DHCPv6 Relay Agent profiles configuration

Step 1. Go to a needed DHCP Relay Agent profile:

ma4000(config)# profile dhcpv6-ra dhcpv6-ra-01

Step 2. Enable DHCP traffic processing, using

enable

command:

ma4000(config-dhcpv6-ra)("dhcpv6-ra-01")# enable

Step 3. If necessary, enable adding of DHCPv6 option 37 and 38 by

add-suboptions

command:

«
...
79
80
81
82
83
...
»

Summary of Contents for MA4000-PX






















































































































































































Reviews:

No comments

Related manuals for MA4000-PX

Brand: NEC Pages: 72

ELECTRA ELITE IPK II

Brand: NEC Pages: 617

VERSA DOCK - SERVICE

Brand: NEC Pages: 8

Brand: PaloAlto Networks Pages: 2

Brand: Quantum Pages: 20

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

Brand: Furuno Pages: 24

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: LogLogic Pages: 30

Brand: Baldor Pages: 34

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brand: NETGEAR Pages: 2

Brand: Taiwan Commate Computer Inc. Pages: 29

BPTA-CPUMS-V2-SKA

Brand: Bitspower Pages: 6

PowerBeam PBE-5AC-400-ISO

Brand: Ubiquiti Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands