ELTEX MA4000-PX Operation And Maintenance Manual Download Page 61

Page: 61 / 181

User Manual, Part III 61

Subscriber access/aggregation node МA4000-РХ

Step 7. If necessary, enable or disable the capability to send packets from this interface to another

one (or a range of interfaces) by using the

bridging to

command. Pass interface type and number (or a

range) as parameters. The interface types and numbers are given in

Table 14

ma4000(front-port-1/0)# bridging to front-port 1/1

Step 8. Set automatic determination of speed and duplex of the interface either by using the

speed auto

command or manually.

ma4000(front-port-1/0)# speed auto

Step 9. Apply the configuration using the

commit

command.

ma4000(front-port-1/0)# do commit

15.3

GPON Interfaces Configuration

Step 1. Switch to the

configure view.

ma4000# configure terminal

Step 2. Activate traffic encryption with the gpon olt encryption command, if necessary. Specify

encryption key renewal period with the gpon olt encryption key-update command. Pass the time period
in seconds as a parameter.

ma4000(config)# gpon olt encryption
ma4000(config)# gpon olt encryption key-update 60

Step 3. Specify ONT authentification method with the

gpon olt authentication

command.

ma4000(config)# gpon olt authentication both

Step 4. Switch to GPON interface configuration.

ma4000(config)# interface gpon-port 0-7

Step 5. Enable or disable interfaces with the

no shutdown

shutdown

command respectively, if

necessary.

ma4000(config)(if-gpon-0-7)# no shutdown

Step 6. Activate FEC for the interface with the

fec

command, if necessary.

ma4000(config)(if-gpon-0-7)# fec

Step 7. Adjust time settings of optical transceiver if needed.

ma4000(config)(if-gpon-0-7)# optics use-custom
ma4000(config)(if-gpon-0-7)# optics ...

Optical transceiver should be adjusted only by agreement with Eltex Service Center.

Step 8. Apply the configuration by using the

commit

command.

ma4000(config)(if-gpon-0-7)# do commit

Summary of Contents for MA4000-PX






















































































































































































Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands

ELTEX MA4000-PX, Operation And Maintenance Manual

Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands