ELTEX MA4000-PX Operation And Maintenance Manual Download Page 160 | Manualshive

Page: 160 / 181

background image

160

User Manual, Part V

Subscriber access/aggregation node МA4000-РХ

42

ONT MONITORING

42.1

ONT Configurations List

Step 1. To view ONT active configurations, execute the

show interface ont <SLOT>/<PORT>

configured

command.

ma4000# show interface ont 0/0 configured

-----------------------------------
Slot 0 GPON-port 0 ONT configured list
-----------------------------------

  ## Serial ONT ID Assigned channel Description
1 0000000000000000 0 0

Slot 0 total ONT count: 1

42.2

Active ONT List

Step 1. To view ONT empty configurations, execute the

show interface ont <SLOT>/<PORT>

unconfigured

command.

ma4000# show interface ont 0/0 unconfigured

Slot 0 GPON-port 0 has no unconfigured ONTs
Slot 0 total ONT count: 0

42.3

Online ONT List

Step 1. To view online ONT list, execute the

show interface ont <SLOT>/<PORT> online

command.

ma4000# show interface ont 0-15/0-7 online

Slot 0 GPON-port 0 has no online ONTs
Slot 0 GPON-port 1 has no online ONTs
Slot 0 GPON-port 2 has no online ONTs
Slot 0 GPON-port 3 has no online ONTs
Slot 0 GPON-port 4 has no online ONTs
Slot 0 GPON-port 5 has no online ONTs
Slot 0 GPON-port 6 has no online ONTs
Slot 0 GPON-port 7 has no online ONTs

Slot 0 total ONT count: 0

Table 28

—

Description of ONT States

ONT State

Description

UNACTIVATED

ONT has no configurations

ALLOCATED

ONT detected

AUTHINPROGRESS

ONT authentication is in progress

AUTHFAILED

Authentication failed

AUTHOK

Authentication successfully completed

«
...
158
159
160
161
162
...
»

Summary of Contents for MA4000-PX






















































































































































































Reviews:

No comments

Related manuals for MA4000-PX

Brand: Quatech Pages: 27

X-Pedition 2000

Brand: Enterasys Pages: 86

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

Brand: DigiTech Pages: 6

PowerBeam PBE-5AC-400-ISO

Brand: Ubiquiti Pages: 23

Brand: LevelOne Pages: 3

Brand: Comelit Pages: 140

Brand: Honeywell Home Pages: 36

Brand: R.V.R. Elettronica Pages: 171

RJModem MT5656RJ

Brand: Multi-Tech Pages: 27

Brand: Avaya Pages: 2

Brand: ADLINK Technology Pages: 29

INTEL CORE i5 SYSTEM BOARD

Brand: Aprotech Pages: 154

POA-MD17SDID - Projector Terminal Expansion Board

Brand: Sanyo Pages: 4

SPEEDSTREAM SS1021

Brand: Siemens Pages: 40

Brand: Ralink Pages: 93

Brand: Trust Pages: 49

Transient Designer 9946

Brand: SPL Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands