ELTEX MA4000-PX Operation And Maintenance Manual Download Page 154 | Manualshive

Page: 154 / 181

background image

154

User Manual, Part V

Subscriber access/aggregation node МA4000-РХ

40.4

PP4X Interface Statistics Preview

Step 1. To view the PP4X interface statistics, execute the

show interface <id> counters

command:

PP4X interfaces include: front-port, slot-port.

ma4000# show interface front-port 1/0-5 counters
Port UC recv MC recv BC recv Octets recv
--------------- ------------- -------------- --------------   --------------
--
front-port 1/0 28880 60669 25654 15133168
front-port 1/1 0 0 0 0
front-port 1/2 0 0    0 0
front-port 1/3 0 0 0 0
front-port 1/4 0 0 0 0
front-port 1/5 0 0 0 0
Port UC sent MC sent BC sent Octets sent
--------------- --------------  --------------       ---------------      ---------------
-
front-port 1/0 25710 3426 18 2523658
front-port 1/1 0 0 0 0
front-port 1/2 0 0 0 0
front-port 1/3 0 0 0 0
front-port 1/4 0      0 0 0
front-port 1/5 0 0 0 0

Step 2. For detailed statistics, use the

show interface <id> counters detail

command:

ma4000# show interface front-port 1/0 counters detail
Counter Value
------------------------------ --------------------
UC sent 127
MC sent      13
BC sent 8
Octets sent 11899
UC recv 182
MC recv 131
BC recv 50
Octets recv 40473
Bad octets recv 0
MAC transmit err    0
Bad frames recv 0
Frames 64 octets pass 47
Frames 65-127 octets pass 320
Frames 128-255 octets pass 142
Frames 256-511 octets pass 2
Frames 512-1023 octets pass 0
Frames 1024-max octets pass 0
Excessive collisions 0
Unrec MAC cntr recv      0
FC sent 0
Good fc recv 0
Drop events 0
Undersize packets 0
Fragments packets 0
Oversize packets 0
Jabber packets 0
MAC receive err 0
Bad CRC     0
Collisions 0
Late collisions 0
Bad FC recv 0
Current load Kbits sent/sec 1
Current load Kbits recv/sec 3
Current load frames sent/sec 2
Current load frames recv/sec 5
5:00 average Kbits sent/sec 0

«
...
152
153
154
155
156
...
»

Summary of Contents for MA4000-PX






















































































































































































Reviews:

No comments

Related manuals for MA4000-PX

Brand: Sangoma Pages: 6

Brand: Patton electronics Pages: 51

Brand: Idis Pages: 86

Brand: Paradyne Pages: 2

Protege PRT-PX16-PCB

Brand: ICT Pages: 34

Brand: Campbell Pages: 38

Brand: Cypress Semiconductor Pages: 16

SmartMesh IA-510 D2511

Brand: Dust Networks Pages: 30

Brand: Kaptia Pages: 14

Brand: Navitar Pages: 1

Brand: Hama Pages: 25

Brand: ZALMAN Pages: 18

Brand: Corsair Pages: 12

Network Scanning Unit A

Brand: Ricoh Pages: 206

Brand: Intel Pages: 20

Soundweb 9088ii DSP System

Brand: BSS Audio Pages: 2

Brand: DAPAudio Pages: 33

ROADRECORDER 8400 NVR

Brand: Safety Vision Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands