ELTEX MA4000-PX Operation And Maintenance Manual Download Page 143 | Manualshive

Page: 143 / 181

background image

User Manual, Part V 143

Subscriber access/aggregation node МA4000-РХ

37

GENERAL INFORMATION

37.1

View Current SW Version of Access Node

To view information on the current SW version,

show firmware

command shall be used.

ma4000# show firmware

Firmware status:
~~~~~~~~~~~~~~~~
Unit Image Running Boot Version Date
---- ----- ------- ----------- ------------------- --------------------
-
1 0 No 1 3 2 335 40605 23-Oct-2014 09:06:46
1 1 Yes * 1 3 2 340 40625 24-Oct-2014 20:06:55
2 0 Yes     * 1 3 2 340 40625 24-Oct-2014 20:06:55
2 1 No 1 3 2 335 40605 23-Oct-2014 09:06:46

"*" designates that the image was selected for the next boot

37.2

View Information on Access Node

To view information on PP4X modules,

show system information

command shall be used. PP4X

module number shall be specified as a parameter.

ma4000# show system information 1
System information (1):
  Uptime (d:h:m:s): 5:22:26:57
  CPU load (1/5/15 minutes): 0.00/0.01/0.00
  RAM (total/free), Mbytes: 498/287
  Partition '/' (total/free), Mbytes: 57/23
  Partition '/mnt/tools' (total/free), Mbytes: 1024/934
  Partition '/mnt/config' (total/free), Mbytes: 64/61
  Partition '/mnt/log' (total/free), Mbytes: 128/123
  Temperature (SFP): 35C
  Temperature (CPU): 42C
  Temperature (Switch) : 49C
  Firmware version: 3.22.0.189 r39940 05:32:45 04/09/2014
  Linux  version:  Linux  version  2.6.22.18  ([email protected])  (gcc
version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #1 Thu Sep 4 12:02:21 NOVT 2014
  MAC address: a8:f9:4b:88:33:a0
  Serialnumber: OL02000580

To view information about the crate,

show system environment

command shall be used.

ma4000# show system environment
MFC board status: ok
MFC board version: 0x2
MFC firmware:
  Status: 0x00 (ok)
  Version: 8 2 1 1 5 05/11/2013
  Timestamp (UTC): 05-Nov-2013 12:19:22

Fan configured speed, %: auto
Fan current speed, %: 46
Fan minimum speed, %: 15
Fan speed levels, %: 15 25 36 46 57 68 78 89 100

Fan0 Fan1 Fan2
Status: ok ok ok

«
...
141
142
143
144
145
...
»

Summary of Contents for MA4000-PX






















































































































































































Reviews:

No comments

Related manuals for MA4000-PX

Brand: 3Com Pages: 2

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: Q-See Pages: 2

EXPANSION CARD X-DANTE

Brand: Behringer Pages: 65

Brand: Galaxy Pages: 30

Brand: Marani Pages: 39

Brand: XJTAG Pages: 9

Brand: Xilinx Pages: 8

Brand: Atmel Pages: 2

Brand: Cypress Semiconductor Pages: 19

Brand: Gearlinx Pages: 23

Brand: IBM Pages: 64

Brand: Softing Pages: 16

Brand: Raven Pages: 33

Brand: Magewell Pages: 10

Brand: Z3 Technology Pages: 18

Brand: Keithley Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands