ELTEX MA4000-PX Operation And Maintenance Manual Download Page 135 | Manualshive

Page: 135 / 181

background image

User Manual, Part IV 135

Subscriber access/aggregation node МA4000-РХ

Step 2. Set the "IP Host" identifier to 0.

ma4000(config-cross-connect)("TR069")# iphost eid 0

Step 3. Check the changes.

ma4000(config-cross-connect)("TR069")# do show profile cross-connect TR069
  Name: 'TR069'
  Description:                                       'ONT Profile Cross Connect
10'
  Model: ont-rg
  Bridge group: -
  Tag mode: single-tagged
  Outer vid:       1
  Outer cos: unused
  Inner vid:   -
  U vid: untagged
  U cos:       unused
  Mac table entry limit: unlimited
  Type: management
  Iphost eid: 0
  Priority queue:      0

Step 4. Apply the changes by using the

do commit

command.

ma4000(config-cross-connect)("TR069")# do commit

34.3

Configuration of a TR-069 OOB Management Channel

Not all ONT vendors support TR-069 Inband management channel. An OutOfBand alternative

management channel is developed for this case. The main peculiarity of the mode is that is uses a
separate bridge for management. Provided below is a part of the OMCI scheme. Arrows show the traffic
flow.

Fig. 44—TR-069 OutOfBand Management Channel

«
...
133
134
135
136
137
...
»

Summary of Contents for MA4000-PX






















































































































































































Reviews:

No comments

Related manuals for MA4000-PX

Brand: TC Electronic Pages: 2

Brand: dbx Pages: 2

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: Omron Pages: 13

Brand: Aaeon Pages: 61

Brand: MFJ Pages: 11

Brand: Supermicro Pages: 131

Brand: Qlogic Pages: 2

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brand: ZALMAN Pages: 6

Brand: AXIOMTEK Pages: 2

Internet Security Appliances

Brand: SonicWALL Pages: 293

GPX-N 1080Ti-M23

Brand: Alphacool Pages: 4

Brand: Crown Pages: 7

Brand: FabiaTech Pages: 86

Application Module 9109 OCU-DP

Brand: Paradyne Pages: 8

AN5506-04 Series

Brand: FiberHome Pages: 146

StorageGRID Webscale SG5700 Series

Brand: NetApp Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands