Wireless DALI gateway
FDG62-230V
GB
Temperature at mounting location:
-20°C up to +50°C.
Storage temperature: -25°C up to +70°C.
Relative humidity:
annual average value <75%.
30 100 868 -
1
Only skilled electricians may install this
electrical equipment otherwise there is
the risk of fi re or electric shock!
valid for devices from production week
27/22
(see bottom side of housing)
Wireless DALI Gateway, bidirectional.
Only 0.5 watt standby loss.
For installation.
49x51 mm, 20mm deep.
The connection terminals are plug-in ter-
minals for conductor cross-sections from
0,2mm² to 2,5mm².
The convenient tap technology permits the
teach-in of up to 32 wireless universal
pushbuttons, wireless direction push but-
tons, wireless central control pushbuttons,
motion sensors, tunable white and intensity
double rocker pushbuttons.
Bidirectional wireless switchable.
Power supply 230V at terminals N and L.
The DALI bus power supply DL-N2-80mA and
up to 40 DALI devices are connected to the
DALI terminals.
The gateway FDG62 controls DALI devices
with Enocean wireless transmitters.
Only
broadcast
commands can be sent.
The FGD62 internally saves the dimming
value and supplies this value as feedback.
The same feedback telegrams are generated
as for an FD62NPN.
Actuators can then be activated by the
feedback signals.
The FDG62 ful ls the function of the DALI
master.
Installation:
After switching on the supply voltage, the
complete DALI bus is scanned, the connected
lamps are switched on with maximum
brightness and dimmed down to minimum
brightness, this can take a few seconds.
The teaching mode is then automatically
active for 2 minutes if the memory content
is empty (delivery status) or if the teaching
mode was not locked. The readiness for
programming is signaled by briefly switching
the lamp on and off.
If there is no action for 2 minutes, the teaching
mode will be ended automatically. This is
signaled by the lamp briefly switching on
and off.
Teaching-in sensors:
Universal pushbutton:
tap briefly 3
times;
Direction pushbutton:
tap briefly 4
times;
Direction buttons are automatically fully
taught-in when tapped. There where is
typed, is then for switching on defined,
the other side for turning off.
Central control button:
tap briefly 5 times;
central control buttons are automatically
taught in completely when tapped.
Central ON is where you tap, the other
side is central OFF.
White tone and intensity double rocker
switch:
6 short taps.
Wireless motion sensor FB55B,
FBH55SB:
(EEP:A5-07-01).
Rotary button and GFVS:
(EEP:A5-38-08);
When teaching-in, the confirmation tele-
grams are switched on and sent automa-
tically. The teaching mode is automatically
blocked here. After a button has been
taught-in, this is confirmed by the lamp
briefly switching on and off, the teach-in
mode is active for a further 2 minutes.
To prevent unintentional teach-in, the
teach-in mode is automatically blocked
2 minutes after the last teach-in. This
is signaled by the lamp briefly switching
on and off twice.
Unencrypted and encrypted sensors can
be taught in.
Teach in encrypted sensors:
1. Activate teach-in mode if necessary.
2. Activate sensor encryption within
2 minutes.
3. Then teach in the encrypted sensor as
described under 'Teach in sensors'.
With encrypted sensors, use the 'rolling
code', i.e. the code changes in each tele-
gram, both in the transmitter and in the
receiver.
If a sensor sends more than 50 telegrams
when the actuator is not active, the sensor
is no longer recognised by the active
actuator and must be taught in again as
'encrypted sensor'. It is not necessary to
teach in the function again.
Typical connection
N
L
L
N
N
DA
LI
230V AC
DA
LI
D
A
LI-B
us
-Netz
te
il
D
L-N
2-
80mA
N
DA
LI
DAL
I -
L
E
D
-
dr
iver
-
+
LE
D
-
spot
