Elster EK280 Applications Manual Download Page 8 | Manualshive

Page: 8 / 163

Elster EK280 Applications Manual Download Page 8

EK280

Application Manual

6

2

EK280 Operation and Display

2.1

Display configuration

2.1.1

"Main" main display

With the calibration lock open,

"Main"

on the

"Ctrl."

display tab allows you to select different views and contents

for the

"Main"

tab:

"

Main

"

Description

meas.

Displayed: Volume at base conditions, volume at measurement conditions,
pressure, temperature, compressibility and conversion factor with short descriptions
Meter reading format: 8 digits before and 3 digits after decimal point

volume short

Displayed: Volume at base conditions and volume at measurement conditions with
short descriptions and header
Meter reading format: 8 digits before and 3 digits after decimal point

volume long

Displayed: Volume at base conditions and volume at measurement conditions with
header but without short descriptions
Meter reading format: 9 digits before and 4 digits after decimal point

Volume, p,T,Q

Displayed: Volume at base conditions, volume at measurement conditions,
pressure, temperature, standard load and operational load with short descriptions
Meter reading format: 8 digits before and 3 digits after decimal point

List

Displayed: Volume at base conditions, volume at measurement conditions, total
number of DE1 inputs (initial number for connected Encoder), pressure,
temperature, conversion factor, compressibility, operational load, standard load,
date and time

Vb, Vo, meas.

The following are displayed: Volume at base conditions, meter reading of the gas
meter (Encoder), pressure, temperature, compressibility ratio factor and conversion
factor with short descriptions
Meter reading format: 8 digits before and 3 digits after decimal point

Vb,Vo,p,T,Q

The following are displayed: Volume at base conditions, meter reading of the gas
meter (Encoder), pressure, temperature, standard load and operational load with
short descriptions
Meter reading format: 8 digits before and 3 digits after decimal point

2.1.2

Setting the number of tabs

With the calibration lock open, on the "

Ctrl.

" display tab the

"Menu"

value allows you to select the number of

tabs displayed.

"

Menu

"

Description

2 registers

The

Main

and

Ctrl.

tabs will be displayed.

3 registers

The

Main

,

Cust.

and

Ctrl.

tabs will be displayed.

4 registers

The

Main

,

Cust.

,

Admin

and

Ctrl. tabs

will be displayed.

5 registers

All

Main

,

Cust.

,

Admin

,

Serv.

and

Ctrl.

tabs will be displayed.

-

This option is system-generated and is not intended for use. It works in the same
way as "

2 registers

" (see above).

«
...
6
7
8
9
10
...
»

Summary of Contents for EK280




































































































































































Reviews:

No comments