Elspec G3500 BlackBox User And Installation Manual Download Page 337

Page: 337 / 358

337

Reset Your Portable BLACKBOX

The Reset Button serves mainly two purposes:



Restore all the Default Factory Settings

: Meaning that all the configurations that

have been set for the device will be deleted & returned to the factory defaults. This
includes

Disabling the PQZIP Recording



Verify that LED Signals are operating & functioning properly

RESET THE PORTABLE BLACKBOX



Ensure that the

Portable BLACKBOX is switched ON

and that Operational Status Indicator

should be either solid blue or red



Access the reset button with either a sharp instrument or a small screwdriver:



Press and hold the reset button



After 5 seconds all the LEDs will turn ON. At that stage you may inspect the LED Signals &
check that they are working



After another additional 8 seconds the Portable BLACKBOX will reboot & restore all factory
default settings.

SEE ALSO:



Attach Temperature Connection

Summary of Contents for G3500 BlackBox







































































































































































































































































































































































Search results

Summary of Contents for G3500 BlackBox

Reviews:

Related manuals for G3500 BlackBox

Brands by name

Popular brands

Elspec G3500 BlackBox, User And Installation Manual

Search results

Summary of Contents for G3500 BlackBox

Reviews:

Related manuals for G3500 BlackBox

Brands by name

Popular brands