background image

5

Installation and commissioning

Ventilation Unit WL610

 • Date of issue: 25.05.2011 • Technical changes reserved. Errors reserved.

Note: 

The delivered colour tones are similar to the RAL colours specified. Deviations

due to technical reasons are possible. Due to the different nature of the surface of the
panel and ventilator housing, slightly different degrees of lustre can occur.

1.1.3. Ventilation levels

Order of the ventilation levels:

2.

Installation and commissioning

2.1. Notes on installation

Warning, mains voltage! 
National legal regulations are to be observed. 

Installation, inspection, commissioning and troubleshooting of the 
device must only be carried out by a competent electrician.

Disconnect all lines to be assembled, and take safety precautions against accidental
switch-on.

The device is exclusively intended for appropriate use. With each inappropriate change
or non-observance of the instructions for use, any warranty or guarantee claim will be
void.

Level

Flap

Blower

Extraction 8

opened

runs, highest speed

Extraction 7

opened

runs

Extraction 6

opened

runs

Extraction 5

opened

runs

Extraction 4

opened

runs

Extraction 3

opened

runs

Extraction 2

opened

runs, lowest speed

Extraction 1

opened

stopped

Off

closed

stopped

Recirculation 1

closed

runs, lowest speed

Recirculation 2

closed

runs

Recirculation 3

closed

runs

Recirculation 4

closed

runs

Recirculation 5

closed

runs

Recirculation 6

closed

runs

Recirculation 7

closed

runs

Recirculation 8

closed

runs, highest speed

Summary of Contents for WL610









Reviews: