elsner elektronik Salva KNX basic Installation And Operation Manual Download Page 14

Page: 14 / 74

Installation and commissioning

Smoke alarm Salva KNX

• Version: 09.09.2016 • Technical Changes and Errors excepted.

Remove the protective foil form one side of the adhesive pad and attach the pad in the
middle of the alarm skirting. Then remove the protective foil on the other side and at-
tach the skirting by firmly pressing it to the ceiling.

2.4.3. Connection

The supply line of the smoke alarm occurs via a 9 V battery. In addition, the KNX mod-
ule receives the bus voltage via the KNX terminal.

WARNING!
Danger of explosion in case of improper handling of the battery!
Property damage by battery leakage.

•

Do not recharge batteries.

•

Do not short-circuit batteries.

•

Do not force batteries open or damage them

•

Do not bring batteries in contact with fire, water or high
temperatures.

ATTENTION!
Do not use rechargeable batteries or mains units for voltage
supply!

•

In case of mains voltage, the device would be out of order
if the mains is out and could not signal any fire.

•

The lower rechargeable battery voltage would trigger
a low battery capacity alarm.

Fig. 7

1. Connect the battery (check for correct polar-
ity!) and insert it into the battery compartment.

2. Connect the device to the KNX bus via the
pluggable terminal (+|-).

KNX

Summary of Contents for Salva KNX basic











































































Search results

Summary of Contents for Salva KNX basic

Reviews:

Related manuals for Salva KNX basic

Brands by name

Popular brands

elsner elektronik Salva KNX basic, Installation And Operation Manual

Search results

Summary of Contents for Salva KNX basic

Reviews:

Related manuals for Salva KNX basic

Brands by name

Popular brands