Weather Station P03i-GPS
1
Weather Station P03i-GPS
• Version: 06.08.2020 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de •
Technical Service: +49 (0) 7033 / 30945-250
EN
P03i-GPS
Weather Station
Technical specifications and installation instructions
Item number 30114
1.
Description
The
Weather Station P03i-GPS
for WS1/1000 Color/Style and WS1000 Connect
measures temperature, wind speed and brightness. It recognises precipitation and
receives the GPS signal for time and location (international time signal and positi-
on).
The weather station is suitable as accessory for KNX WS1000 Color/Style and as
spare part for WS1 Color/Style and WS1000 Color/Style which were produced from
July 2016 on. For older models of the controls please ask Elsner Elektronik for the
suitable weather station model.
1.1. Scope of delivery
•
Weather station with a combination wall/pole mount
1.2. Technical specifications
The product conforms with the provisions of EU directives.
2.
Installation and commissioning
2.1. Installation notes
Installation, testing, operational start-up and troubleshooting should
only be performed by an electrician.
CAUTION!
Live voltage!
There are unprotected live components inside the device.
•
National legal regulations are to be followed.
•
Ensure that all lines to be assembled are free of voltage and take
precautions against accidental switching on.
•
Do not use the device if it is damaged.
•
Take the device or system out of service and secure it against
unintentional use, if it can be assumed, that risk-free operation is
no longer guaranteed.
The device is only to be used for the intended purpose described in this manual. Any
improper modification or failure to follow the operating instructions voids any and
all warranty and guarantee claims.
After unpacking the device, check it immediately for possible mechanical damage.
If it has been damaged in transport, inform the supplier immediately.
The device may only be used as a fixed-site installation; that means only when as-
sembled and after conclusion of all installation and operational start-up tasks and
only in the surroundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may
occur after publication of these operating instructions.
2.2. Installation position
Choose an installation position in the building where wind, rain and sun can be mea-
sured unhindered by the sensors. The weather station must not be installed under-
neath any structural parts from which water can still drip onto the rain sensor after
it has stopped raining or snowing. The weather station must not be shaded by an-
ything, such as building structures or trees.
At least 60 cm of clearance must be left all round the weather station. This facilitates
correct wind speed measurement without eddies. The distance concurrently pre-
vents spray (raindrops hitting the device) or snow (snow penetration) from impai-
ring the measurement. It also does not allow birds to bite it.
Please take note that an extended awning does not shade the device from sun and
wind.
Temperature measurements can also be affected by external influences such as by
warming or cooling of the building structure on which the sensor is mounted, (sun-
light, heating or cold water pipes).
Magnetic fields, transmitters and interfering fields from electricity consumers (e.g.
fluorescent lamps, neon signs, switched-mode power supplies etc.) can interfere
with or even cut out reception of the GPS signal.
2.3. Attaching the mount
The weather station comes with a combination wall/pole mount. The mount comes
adhered by adhesive strips to the rear side of the housing.
Fasten the holder vertically to the wall or pole.
Housing
Plastic material
Colour
White / translucent
Mounting
On-wall
Protection category
IP 44
Dimensions
approx. 96 x 77 x 118 (W x H x D, mm)
Weight
approx. 160 g
Ambient temperature
Operation -30…+50°C, Storage -30…+70°C
Operating voltage
24 V DC
Heating rain sensor
approx. 1.2 W
Measurement range
temperature
-40…+80°C
Resolution (tempera-
ture)
0.1°C
Accuracy (temperature)
±1.5°C at -25…+80°C
Measurement range
wind
0…35 m/s
Resolution (wind)
0,1 m/s
Accuracy (wind)
at ambient temperature -20…+50°C:
±22% of the measurement value when inci-
dent flow is
from 45…315°
±15% of the measurement value when inci-
dent flow is
from 90…270°
(Frontal incident flow corresponds to 180°)
Measurement range
brightness
0 lux ... 99.000 lux
Resolution (brightness)
1 lux at 0 … 999 lux
1 klux at 1 … 99 klux
Accuracy (brightness)
± 35%
Fig. 1
There must be at least 60 cm of space
below, to the sides and in front of the
weather station left from other ele-
ments (structures, construction parts,
etc.).
60 cm
Fig. 2
The weather station must be mounted
on a vertical wall (or a pole).
Wall
or
pole
Fig. 3
The weather station must be mounted
in the horizontal transverse direction
(horizontally).
Horizontal
Fig. 4
For installation in the northern hemis-
phere, the weather station must be
aligned to face south.
For installation in the southern hemis-
phere, the weather station must be
aligned to face north.
North
South
Fig. 5
For wall mounting: Flat side to the wall,
crescent moon-shaped crosspiece facing
up.
Collar
Fig. 6
For pole mounting: curved side to the
pole, crosspiece facing down.
Collar
