elsner elektronik 70251 Installation And Adjustment Download Page 21

Page: 21 / 22

ETS Database Parameters

KNX B4 Universal Interface

• Version: 13.09.2021 • from application 1.0 • Technical changes and errors excepted.

Channel C/D accordingly.

6.3.2. Two-button shutter

Channel C/D accordingly.

Interlock

disabled • enabled

If Interlock is active, changes at the Input are not considered until the Interlock is deacti-
vated again.

Contact type - Channel A

normally open • normally closed

Defines the contact type at the input, NO or NC. If NO is selected, the input is logic high
after the contact is closed.

Contact type - Channel B

normally open • normally closed

Defines the contact type at the input, NO or NC. If NO is selected, the input is logic high
after the contact is closed.

Shutter function A/B

up/down • down/up

Defines the inputs for moving the shutter up and for moving the shutter down.
up/down: • Channel A moves the shutter up.

• Channel B moves the shutter down.

down/up: • Channel A moves the shutter down.

• Channel B moves the shutter up.

Long button press after

0.3...30.0 s; 2.0 s

Time the input needs to be logical high to start the long operation. If the input is logical
high for a shorter time, only the command for short operation will be sent.

Interlock

disabled • enabled

If Interlock is active, changes at the Input are not considered until the Interlock is deacti-
vated again.

Summary of Contents for 70251























Search results

Summary of Contents for 70251

Reviews:

Related manuals for 70251

Brands by name

Popular brands

elsner elektronik 70251, Installation And Adjustment

Search results

Summary of Contents for 70251

Reviews:

Related manuals for 70251

Brands by name

Popular brands