background image

07282020JA 

 

www.elitescreens.com

 

 

 

Aeon CLR® 3 Series 

EDGE FREE

® 

Ceiling Ambient Light 

Rejecting Fixed Frame Projection Screen 

User’s Guide (Z-Type) 

____________________________________________________________________________________ 
 

Product Description: 

The Aeon CLR® 3 Series is an ultra-short throw fixed frame projection screen that uses Elite’s EDGE FREE 
CLR®  technology.  It  is  designed  for 

tabletop  ultra-short  throw  Projectors  only

,  for  use  in  environments 

where ceiling light cannot be entirely controlled. It includes an LED backlight kit and a bezel trim to further 
enhance the frame appearance.  
 

Screen Maintenance  

Dust,  dirt,  and  scratches  on  the  projection  screen  surface  will  affect  the  quality  and  performance  of  the 
projection image.  For optimal results we advise to pay attention to the following instructions.  
 

1)

 

The screen surface has a horizontal lenticular structure

. DO NOT

 wipe the screen up and down or in 

a circular motion. 

Wipe from left to right only

.  

2)

 

Clean the dust on the screen surface with a soft brush or microfiber cloth. A rough/coarse towel or 

cloth may damage the screen’s optical/lenticular surface. 

3)

 

Gently  wipe  the  screen  with  a  lightly  moistened  white  lint  free  cloth  with  water  or  with  a  neutral 
detergent (1mL/0.33 oz) mixed with water (1000 mL/33.8 oz).  

 
Notes: The following precautions should always be followed to avoid damaging the material, which is not 
covered under warranty.  
 

 

Don’t touch the screen material to avoid leaving fingerprints.  

 

Use gloves when handling the material.  

 

Don’t scratch the material, as it will leave permanent markings on the screen’s surface.  

 

Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to the 

material.  

 

Don’t use acetone, benzene, alcohol and any other 

organic solvents to clean the screen material. 

Using such chemicals will permanently damage the screen.

 

 

Frame and Edge Trim Parts 

Qty Item 

Main Frame Parts 

Qty Item 

Edge Trim Parts 

2 pcs 

Vertical Frame (A)  

 

2 pcs 

Vertical Velvet Trim 

 

2 pcs 

½ Horizontal Frame (B) 

 

4 pcs 

½ Horizontal Velvet Trim 

 

2 pcs 

½ Horizontal Frame (C) 

 

 

 

Summary of Contents for Aeon CLR 3 Series








Reviews: