background image

Page 9

011822

1-888-651-3431

PRODUCT WARRANTY & LIABILITY

GENERAL PRODUCT WARRANTY: 

Products purchased from the Authorized Dealer (original place of 

purchase) or Merchant (“Dealer”) will be free of defects in material and workmanship at the time of 

receipt, and will meet the specifications stated at the place of purchase transaction or online at the 

Dealer’s website, under normal use and service when correctly installed, operated and maintained. 

This product warranty is effective for the period of time stated below, unless otherwise stated in the 

product instructions or depicted in the product advertisement. All Authorized Dealer warranties are 

NON-TRANSFERABLE and cover only the original end purchaser. This limited warranty does not 

cover products purchased through non-authorized dealers. Non-authorized dealer receipts are not 

accepted for warranty verification.

***WARRANTY CLAIMS MUST BE MADE DIRECTLY TO THE ORIGINAL PLACE OF PURCHASE.***

WARRANTY PERIOD: 

This warranty remains in force for one year from the date of the product’s 

accepted delivery. The Authorized Dealer offers a one year manufacturer’s warranty for most 

products unless otherwise specified on the product advertisement.

WARRANTY SERVICE: 

The Authorized Dealer will replace any defective or malfunctioning Part at 

no charge, including payment of the shipping costs of Parts or replacement product to and from 

the manufacturer. The purchaser is responsible for labor charges. If the product does not meet 

specifications as depicted in the advertisement, the Authorized Dealer will refund the full purchase 

price of the product.

Questions regarding the warranty on a specific product and warranty claims should be directed to 

the Authorized Dealer with whom the purchase transaction was made.

WARRANTY LIMITATIONS

: The above warranty does not apply to products that are repaired, modified 

or altered by any Party other than the Authorized Dealer; are subjected to unusual physical stress 

or conditions (such as overloaded ramps or corrosion), natural disaster, governmental actions, wars, 

strikes, labor disputes, riots, theft, vandalism, terrorism or any reason beyond reasonable control; 

are damaged due to improper installation, misuse, abuse, accident or negligence in use, storage, 

transportation or handling, or tampering; or to products that are considered consumable items or 

items requiring repair or replacement due to normal wear and tear.

Product should be inspected prior to signing for delivery. Product damage incurred during shipping, 

unless noted on the Bill of Lading at the time of delivery, renders this warranty void.

LIMITED LIABILITY:

 In no event shall 

THE AUTHORIZED DEALER

 be liable to the purchaser or any third 

Party for any indirect, incidental, consequential, special, exemplary or punitive damages arising out 

of the use of the product, including, without limitation, property damage, loss of value of the product 

or any third Party products that are used in or with the product, or loss of use of the product or any 

third Party products that are used in or with the product.

Summary of Contents for BR-STD










Reviews: