background image

Spring

Lever

Cradle Assembly

Brackets

Screw Used

(shown actual size)

2.6 x 7mm

X2

Plate

Big Washers

Screw Used

(shown actual size)

2.6 x 6mm Screws

with Washer

2.6 x 6mm with washer

X2

Input Modular Jack

Buzzer Pad

Remove

Backings

Modular Jack

PC Board

Buzzer 

Screw Used

(shown actual size)

2.6 x 6mm Screws

2.6 x 6mm

X3

Index Label Shield

Index Label

Screws Used

(shown actual size)

Hook Switch

NOTE: Be

sure that the

Lever is above the

Hook Switch as

shown.

3 x 7mm Screws

3 x 7mm

X4

Lever

Decorative Piece

Push Button Panel

NOTE: Push

the Push Button

Panel up and

snap it into

position.

2.6 x 10mm Screws

Screws Used

(shown actual size)

2.6 x 10mm

X2

Handset Assembly

Speaker Pad

Remove
Backing

Speaker

Speaker Pad

Remove
Backing

Mute Button

Keypad Contact

Number

Button

Flash Button

Redial Button

3

2

1

6

5

4

9

8

7

#

0

*

Back View

Use this diagram as a
guide when installing
the number buttons.

NOTE: Make

sure that the angle

on the Flash, Redial,

and Mute buttons are

in the same

direction shown.

Keypad PC Board

Rubber Microphone Cup

Microphone

Screw Used

(shown actual size)

2.6 x 6mm Screws

2.6 x 6mm Screws

2.6 x 6mm

X6

2

5

3

4

Modular Jack

Wiring/Tubing Assembly

NOTE: Follow
these steps for

wiring the speaker

wires to the PC

board wires.

1

Screw Used

(shown actual size)

2.6 x 14mm Screws

Cut Tubing

Slide
Tubing
onto wire.

Twist
wires
together.

Slide
Tubing over
the twisted
wires.

2.6 x 14mm

X2

Wiring/Tubing Assembly

Coiled Cord

NOTE: When

snapping the receiver

cover on, start from the

back.

It may take a couple

attempts to attach

the two pieces.

Phone Number Shield

Phone Number

Label

2.6 x 14mm

Screws

Before the Final

Assembly

Refer to Page 6 and perform the
Transmit/Receive & Dial Tests.

Screw Used

(shown actual size)

2.6 x 14mm

X2

Final Assembly

Foam Feet

Bottom View

Remove
Backing

THIS UNIT COMPLIES WITH

PART 68 FCC RULES FCC NO.

GXA1CHN-74412-TE-E REN NO. 1.3B

USE STRANDARD JACK USOC RJ11C

FCC Label

Line Cord

Copyright © 2001 Elenco Electronics, Inc. All Rights Reserved. • 150 W. Carpenter Ave. • Wheeling, IL  60090 • (800) 533-2441  Fax: (847) 520-0085 • e-mail: [email protected] • Web Site: http://www.elenco.com

You have now completed the assembly of the FUN-755 Telephone Kit. Refer to 

HOW TO USE IT

on

the other side. If the phone does not work, refer to  

TROUBLESHOOTING

.

There are many other               projects: Cassette Player, RC Car, Talking Clocks, Electronic

Keyboard, etc. Ask your store about these projects or call                     at (847) 541-3800.

2.6 x 7mm Screws

Contact Elenco Electronics if you have any problems. Actual colors may vary from those shown here.

ASSEMBLY INSTRUCTIONS

Side View

Top View

Hook

Switch

Lever

Bend LED Up

1/8”

Use scissors
to cut off 1/8”.

FUN-755

FUN-755

Before You

START . . .

Refer to Page 5 and
perform the Ring
Test.

Long Part of Spring

Short Part of Spring

NOTE: Remove any

burrs on the buttons

before installing them into

the Push Button Panel.

2

Remove Burrs

NOTE: This

may take a

couple attempts

to attach the two

pieces.

Reviews: