Manual for the EHC 04 and EHC 58 from November 2019
You don´t like to read manuals? We too... However, it will take only 2 minutes of your time to read it and 10
minutes for the installation and you will have more fun with your new EHC :-)
Just connect the d - sub connector(s) to the EHC. and screw it gentle.
We suggest to fill the connectors
with Di-electric grease before of the installation what helps to prevent the connectors against
moisture.
Every output is short circuit protected and will limit the maximum current between 6 and 20
Ampere after some seconds. The starter solenoid output is rated with maximum currents up to 20 Ampere
depending of the short circuit current and the temperature.
However, we suggest to wire an inline 25 A
fuse in the + 12 Volt line to the harness what will protect the EHC in case of a short circuit at the
starter solenoid wire.
A short circuit increase the temperature of a part in the EHC very fast up to 150
degree Celsius what result in small gaps in the potting material, following that the box is not waterproof
anymore and the durability of the EHC is decreased if you like to ride in the rain...
Adjustment of the different functions:
The EHC can be used in most circumstances without any modification. However, you can easily change a
few functions in the EHC without being a software specialist. Press the "horn" button while switching on the
ignition switch and you are in the "setup" mode. A one time flash will indicate the first option, what is the
"Show flasher" function. Just press the "right" button if you would like to activate it or the "left" button if you
want to switch off this function. After a press on a direction button you will come immediately to mode 2 what
is indicated with 2 flashes of the turn signals. The following options are possible:
Number
of
flashes
Mode
Left flasher button
Right flasher button
Describtion
1 x
Show flasher
Off
On
1 emergency flash when power on
the box
2 x
Flasher auto off
Off
On
The flasher switches off after 40
times
3 x
Brake light mode
The rear light glow
with 30 % if not
braked (EU - mode)
Brake light / rear light
combination (US -
mode)
European / US mode for the
rear light / brake light / direction
indicators
4 x
Brake light flasher
Off
On
The brake light flashes 3 times
before it is permanent on when
you a brake
5 x
Head light off
Head light on
Head light off
Head light status when switching
on the ignition key.
6 x
Neutral / Starter
Neutral switch ignored
Neutral switch active
Starter function depending of the
neutral switch in the gearbox
7 x
Head light / Ignition
Head light off
Head light on
The head light switch off or stay
on when you switch off the ignition
8 x
Ignition status
Key switch (EU mode) Run button (US mode)
You turn on the ignition with the
"run" button or with the key switch
Your settings are stored after choosing the last option.
Your are done ! The EHC will keep your settings
after a power off. However, you can change the settings any time you want.
The following new functions are integrated:
- You can switch off your head light by pressing the head light button for 2 seconds. A further short
press switch on the head light again.
- The starter output is protected and switch off after 10 seconds pressing the start button
- You can start the bike if the neutral switch is closed, but not if the gear box is not in "Neutral" position.
- An overvoltage protection is integrated. It switch off the ignition if overvoltages above 18 Volt are
present for longer than 1 second. 3 led indicate the battery voltage: 1 blue led: < 8 Volt,
2 blue led: between 8 Volt and 18 Volt, red led: > 18 Volt. The horn is on for 2 times if overvoltages
are present. This should help you to identify the ignition status as overvoltage protection.
- A Bluetooth module is availabe as option. You can download the free Android app from our website
and control all bike functions or check the battery voltage via a simple touch on your smart phone.
1 / 2
