Electrolux Saladette 950, Installation And Operating Manual

Page: 13 / 26

13
A.8 Technical data
• The data plate and the energy labelling refer to original manufactured configuration.
• The appliance that can operate at 50 Hz or 60 Hz does not need any setting by the user.
Materials and fluids used
• R290 gas is potentially flammable and explosive. Take every possible precaution to prevent any risk linked to the nature of this
gas during any routine and/or extraordinary operation carried out on the appliance.
A.9 Climatic Class
The climatic class given on the data plate refers to the following values:
• CLIMATIC CLASS: 5
Models with only doors
– 43 ℃ (IEC/EN 60335-2-89)
– 40 ℃ room with 40% relative humidity (EN 16825/EN ISO 22041).
Models with only drawers or mix (drawers and doors)
– 43 ℃ (IEC/EN 60335-2-89)
– 30 ℃ room with 55% relative humidity (EN 16825/EN ISO 22041).
A.10 Transport, handling and storage
• Transport (i.e. transfer of the appliance from one place to another) and handling (i.e. transfer inside workplaces) must occur with
the use of special and adequate means.
• Please refer to indications on packaging for stackability during transport, handling and storage.
• Do not stand under suspended loads during loading or unloading operations. Unauthorized personnel must not enter the work
area.
• The weight of the appliance alone is not sufficient to keep it steady.
• For appliance lifting and anchoring, do not use movable or weak parts such as: casings, electrical raceways, pneumatic parts, etc.
• Do not push or pull the appliance to move it, as it may tip over. Use proper tool to lift the appliance.
• Arrange a suitable area with flat floor for appliance unloading and storage operations.
• Appliance transport, handling and storage personnel must be adequately instructed and trained regarding the safely use of lifting
systems and personal protection equipment suitable for the type of operation carried out.
• When removing the anchoring systems, make sure the stability of the appliance parts does not depend on the anchoring and,
therefore, that this operation does not cause the load to fall off the vehicle. Before unloading the appliance components, make
sure all the anchoring systems are removed.
A.11 Installation and assembly
• The installer must evaluate the minimum volume of the installation’s environment necessary to reduce the risks related to danger
caused by the flammability and toxicity of the refrigerant present in the appliance.
• The operations described must be carried out in compliance with the current safety regulations and provisions in force in the
country of use.
• The machine is not suitable for installation outdoors and/or in places exposed to atmospheric agents (rain, direct sunlight, etc.).
A.12 Electrical connection
• The power supply system must be suitable for the rated current of the connected appliance; the connection must be carried out in
compliance with the regulations and provisions in force in the country of use.
• The information regarding the appliance power supply voltage is given on the dataplate.
• Install between the power cable and the electric line a differential thermal-magnetic switch suitable for the absorption specified
on the data plate, with contact gap enabling complete disconnection in category III overvoltage conditions and complying with the
regulations in force.
For the correct sizing of the switch or plug, refer to the absorbed current specified on the appliance data plate.
• After making the connection, with the appliance running check that the power supply does not fluctuate by ±10% the rated
voltage.
• If the power cable is damaged, it must be replaced by the Customer Care Service or in any case by specialised personnel, in
order prevent any risk.
• The manufacturer declines any liability for damage or injury resulting from breach of the above rules or non-compliance with the
electrical safety regulations in force in the country where the appliance is used.
A.13 Electrical connection for appliances with plug
• To connect to the power supply, insert the power cable plug in the corresponding mains socket, first making sure:
– the socket has an efficient earth contact and the mains voltage and frequency match that given on the dataplate. In case of
any doubts regarding the efficiency of the earth connection have the system checked by specialised personnel.
– the system power supply is arranged and able to take the actual current absorption and that it is correctly executed according
to the regulations in force in the country of use.
• The plug must be accessible after positioning the appliance in the place of installation.
• The plug must be in a position always visible to the operator performing the intervention during maintenance operations.