manualshive.com logo in svg

Electrolux MAGISTAR OVEN 6-10-20GN, Service Manual, Page: 50 / 124

Share
Download
Electrolux MAGISTAR OVEN 6-10-20GN Service Manual Download Page 50

50

D.4.2.1 Appliance parameters (APPL PAr)

The complete parameter list can be found at D.5

Parameters list chart for all level (T, K, B, C)

.

Once entered into the “Service Area“.

By pressing

“0“

you will visualize the parameter list; By pressing the right and left buttons you can scroll

through the parameter list. The value of the desired parameter is again shown by pressing

“0“

.

By pressing the right and left buttons you can change the parameter value. Repressing again

“0“

will save the

new parameter value and return into the parameter list.
By pressing

“8“

you enter into a secondary menu for the default parameters the first is ESC, by pressing again

“8“

you return to the service menu, but by pressing “left-right buttons“ you have a / factory parameters / default

parameters/user upload menu (uploading manually only the parameter list).

Summary of Contents for MAGISTAR OVEN 6-10-20GN





























































































































Reviews:

No comments