background image

0308

10

7

Notice

Date Page

05102004

INSTALLATION 

MANUAL

7. Installation

Table 2 

(correction factors for different ambient 

temperatures)

Table 3 

(correction factors for different cable insulating materials)
 

Insulating 

Max. Working 

Correction

 

material 

Temperature range 

factor

 

PVC ..............................70 °C (158 °F) ........................... 1.00

 

Natural or Synthetic Rubber ............60 °C (140 °F) ........................... 0.92

 

Silicone Rubber ....................120 °C (248 °F) .......................... 1.60

The feeder cable sections mentioned in our literature are given 

only as a guide.

To obtain a value perfectly suited to your own application and which takes account of the 

different correction factors in respect of your plant, refer to the tables below.

Table 1 

(in accordance with EN Standard 60204-1)

Values given for : 

  - Cable with copper conductors. 

  - Cable with PVC insulation (for other insulants see Table 3). 

  - Ambient temperature 40 °C max. (for others see Table 2). 

  - Three-phase cable under load without including starting currents. 

  - BT / C/ E cable layout.

 Maximum Admissible Current

Cable section  Seated in Cable Duct 

Wall 

Cable 

 

 

or Cable Trough 

Fixing 

Tray

 

 

B2 

E

  3 x 1.5 mm² ................. 12.2 A  .....................15.2 A ..................... 16.1 A

  3 x 2.5 mm² ................. 16.5 A  ...................... 21 A .........................22 A

 

3 x 4 mm² ....................23 A ........................ 28 A .........................30 A

 

3 x 6 mm² ....................29 A ........................ 36 A .........................37 A

  3 x 10 mm² ...................40 A ........................ 50 A .........................52 A

  3 x 16 mm² ...................53 A ........................ 66 A .........................70 A

 

3 x 25 m² .....................67 A ........................ 84 A .........................88 A

  3 x 35 mm² ...................83 A ....................... 104 A .......................114 A

  3 x 50 mm² ......................- .......................... 123 A .......................123 A

  3 x 70 mm² ......................- .......................... 155 A .......................155 A

 

Ambient 

Correction   

 

Temperature 

Factor

 

30 °C (86 °F) ..................1.15

 

35 °C (95 °F) ..................1.08

 

40 °C (104 °F) .................1.00

 

45 °C (113 °F) .................0.91

 

50 °C (122 °F) .................0.82

 

55 °C (131 °F) .................0.71

 

60 °C (140 °F) .................0.58

Summary of Contents for IC44819FFS

























































Reviews: