When calling the customer functions no washing cycle
must be selected generally!
6.11. Service function / setting of water hardness
General information
Calling / changing / saving the "electronic" hardness area value
w
Setting and changing the water hardness area is executed in
Calling the function "set water hardness"
all designs resp. key arrangements analogously.
1.
Appliance in switched-off condition
w
For that you always have to use the keys S0, S1, S2 and S3
independent of their variant-depending program load.
2.
Switch on appliance with ON/OFF key S0 -- "prestart" mode
w
Key S1 is ALWAYS the "water hardness area key"
Ä
All LEDs of the program and option keys are lit.
w
The water hardness area value 4 is preset by the manufacturer.
With setting "1L" it is generally not regenerated.
3.
Press keys S2 and S3 simultaneously until the
A salt addition is not necessary.
confirmation LEDs LD1, LD2 and LD3 are flashing.
w
A possibly existing "salt" LED is not selected.
3.
By actuating the function key S1 you now can call the
Electronic and mechanical setting with the appliance:
water hardness function. The confirmation LED LD1
w
In addition to the "electronic" setting on the control panel
continues flashing, LEDs LD2 and LD3 go out.
described on the right you also have to pay attention to the
The set hardness area is indicated in the display and in
mechanical setting in the appliance by the 2-step blending
addition acoustically.
switch. (see for that the table for hardness area values)
( see for that the table on the left side of this page! )
Changing the set hardness
Any other actuation of the function key S1 changes
the hardness area. This increases the value scrolling.
( 4L - 5L - 6L - ... - 10L - 1L - 2L - ... )
Leaving the function
Table for hardness area values:
After the last key pressure of function key S1 you can
leave the special program as follows.
After 60 seconds all LEDs of the program and option keys
are lit automatically. The indication in the display goes out.
The appliance is in the "prestart" mode again
or
the appliance is switched off by the ON/OFF key S0.
Saving the set water hardness
The selected hardness area is saved directly after
any entry.
Verschneide-
schalter
EDW 1503 / VGA
LD1
LD2
LD3
S1
S2
S3
1
99
S0
1.
2.
4.
3.
... AUS nach 60sek. automatisch
S0
S0
Pro
Tastendruck
+ 1 Stufe
S0
S0
... AUS durch manuelle Betätigung über Ein/Aus
LD1
LD2
LD3
LD4
LD5
LD6
S1
S2
S3
S4
S5
S6
LD10
LD11
LD12
LD1
LD2
LD3
LD4
LD5
LD6
LD1
S1
5L
6L
10L
S2
S3
blinken
LD1
LD2
LD3
LD1
S1
blinkt
4L
Ausgabe
zusätzlich
akustisch
blinkt
1L
LD1
LD2
LD3
LD4
LD5
LD6
Anzeige
Display
Anzeige
Ende-LED
Wasserhärte
Bemerkung
Anzahl blinken
elektr..
mech.
in dH
in mmol/L
Bereich
1L
1 mal
1
bis
4
bis
0,7
I
kein Regenerieren
2L
2 mal
2
4
bis
10
0,7
bis
1,8
I / II
3L
3 mal
3
11
bis
14
1,9
bis
2,5
II
4L
4 mal
4
15
bis
18
2,6
bis
3,2
5L
5 mal
5
19
bis
22
3,3
bis
3,9
6L
6 mal
6
23
bis
28
4,0
bis
5,0
7L
7 mal
7
29
bis
36
5,1
bis
6,4
8L
8 mal
8
37
bis
42
6,5
bis
7,5
9L
9 mal
9
43
bis
50
7,6
bis
8,9
10L
10 mal
10
51
bis
70
9,0
bis
12,5
doppelt Regenerieren
Einstellung der
Härtestufe
0
III
IV
1
31
