Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 257

Page: 257 / 322

Doc

E154713

C-19

C: Using the IEC61850 Protocol Ethernet Network Server

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

C.2: Using the Nexus® 1500+ Meter’s IEC 61850 Protocol Ethernet

Network Server

This section contains instructions for understanding and configuring the Nexus®
1500+ meter’s IEC 61850 Protocol Ethernet Network server.

C.2.1: Overview

The IEC 61850 Protocol Ethernet Network card is a Nexus® 1500+ standard I/O

board. It is available via Ethernet port 1 with V-Switch

keys 2 and 3. The IEC 61850

Protocol Ethernet Network server has the following features:

• Standard Ethernet 10/100 Mbps connector is used to link the unit into an Ethernet

network.

• Standard operation port 102, which can be reconfigured to any valid TCP/IP port.

• Up to 6 simultaneous connections can be established with the unit.

• Configurable via the .CID file (XML formatted)

• Embedded Capabilities File (.ICD downloadable from the unit)

• Supports MMS protocol.

• Supports the following Logical Nodes:

• LLN0 (with predefined Sets and Reports)

• LPHD (Identifiers)

• MMXU with

• Phase-to-N voltages

• Phase-to-Phase voltages

• Phase currents

• Per Phase VA

• Total VA

• Per Phase VAR

Summary of Contents for Shark 100T



































































































































































































































































































































Search results

Summary of Contents for Shark 100T

Reviews:

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 257 / 322

Search results

Summary of Contents for Shark 100T

Reviews: