manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 208 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 208

     

Doc

#    

E154713     

                              

              11-24

11: Using the I/O Options

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

11.8.7: Digital Dry Contact Relay Output (Form C) Module

NOTE: 

Only one of these modules may be connected to a Nexus® 1500+ meter. 

The Digital Dry Contact Relay Output module is used to send a control output (electri-
cal signal) when a limit is exceeded, for example to turn on a breaker or sound an 
alarm. 

Digital Dry Contact Relay Output Module Specifications

Model Number

4RO1: 4 matching relay outputs

Contact Type

Changeover (SPDT)

Relay Type

Mechanically latching

Communication

RS485, Modbus RTU

Programmable Baud Rates: 4800, 9600, 19200, 

38400, 57600

Power Requirement

12-20 VDC @50-200 mA; 1500+ supports only one 

module

Operating Temperature

(-20 to +70) 

o

C/(-4 to +158) 

o

F

Switching Voltage

AC 250 V/ DC 30 V

Switching Power

1250 VA / 150 W

Switching Current

5 A

Switching Rate Max.

10/s

Mechanical Life

5 x 10

7 

switching operations

Electrical Life

10

5 

switching operations at rated current

Breakdown Voltage

AC 1000 V between open contacts

Isolation

AC 2500 V surge system to contacts

Reset/Power Down State

No change - last state is retained

Factory Settings

Modbus Address: 156

Baud Rate: 57600

Transmit Delay Time: 0

Default Settings (Reset Button)

Modbus Address: 247

Baud Rate: 57600

Transmit Delay Time: 20 msec

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments