Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 206

Page: 206 / 322

Doc

E154713

11-22

11: Using the I/O Options

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

11.8.6: Analog Transducer Signal Output Modules

Table 1:

Analog Transducer Signal Output Module Specifications

Model Numbers

1mAON4: 4-channel analog output 0±1 mA

1mAON8: 8-channel analog output 0±1 mA

20mAON4: 4-channel analog output 4-20 mA

20mAON8: 8-channel analog output 4-20 mA

Accuracy

0.1% of Full Scale

Over-range

±20% of Full Scale

Scaling

Programmable

Communication

RS485, Modbus RTU

Programmable Baud Rates: 4800, 9600, 19200,

38400, 57600

Power Requirement

12-20 VDC @50-200 mA

Operating Temperature

(-20 to +70)

C/(-4 to +158)

Maximum Load Impedance

0±1 mA: 10 k ; 4-20 mA: 500

Factory Settings

Modbus Address: 1mAON4: 128; 1mAON8: 128;

20mAON4: 132; 20mAON8: 132

Baud Rate: 57600

Transmit Delay Time: 0

Default Settings (Reset Button)

Modbus Address: 247

Baud Rate: 57600

Transmit Delay Time: 20 msec



Summary of Contents for Shark 100T



































































































































































































































































































































Search results

Summary of Contents for Shark 100T

Reviews:

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 206 / 322

Search results

Summary of Contents for Shark 100T

Reviews: