Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 205

Page: 205 / 322

Doc

E154713

11-21

11: Using the I/O Options

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

11.8.5: Factory Settings and Reset Button

Factory Settings

All external I/O modules are shipped with a preset address and a baud rate of 57600.
See following sections for I/O Module addresses.

Reset Button:

If there is a communication problem or if you are unsure of a module's address and
baud rate, press and hold the

Reset

button for 3 seconds; the module resets to a

default address of 247 at 57600 baud rate for 30 seconds.

Summary of Contents for Shark 100T



































































































































































































































































































































Search results

Summary of Contents for Shark 100T

Reviews:

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 205 / 322

Search results

Summary of Contents for Shark 100T

Reviews: