Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 201

Page: 201 / 322

Doc

E154713

11-17

11: Using the I/O Options

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Figure 11.5: PSIO Label

11.8.4: Using PSIO with Multiple I/O Modules

NOTE: PSIO must be to the right of the I/O modules, when viewing its side label (as
shown in the figure below).

Figure 11.6: PSIO with Multiple External I/O Modules

POWER +
POWER -

DANGER

L(+)

Power Supply

PSIO

Max Power: 12 VA

Input Voltage: 12-60V DC

www.electroind.com

Output Voltage: 12V DC

ElectroIndustries/GaugeTech

90-240V AC/DC

N(-)

Power In

www.electroind.com

Electro Industries/Gaugetech

Power Supply

Max Power: 12 VA

Input Voltage: 90-240V AC/DC

Output Voltage: 12V DC

PSIO

Power In

L(+)

N(-)

DANGER

L(+)

Power Supply

PSIO

Max Power: 12 VA

Input Voltage: 90-240V AC/DC

www.electroind.com

Output Voltage: 12V DC

ElectroIndustries/GaugeTech

N(-)

Power In

RESET

COM

INPUT 1

INPUT 2

INPUT 3

INPUT 4

0-1mA

Analog Input

Module

INPUT 5

INPUT 6

INPUT 7

INPUT 8

RESET

COM

INPUT 1

INPUT 2

INPUT 3

INPUT 4

0-1mA

Analog Input

Module

INPUT 5

INPUT 6

INPUT 7

INPUT 8

RESET

COM

OUT 1

OUT 2

OUT 3

OUT 4

0-1mA

Analog Output

Module

Reset Button

I/O Port (Size and

in configuration vary)

LEDs

Communication
ONLY
(A+, B- and
Shield)

Female

RS485

Side Port

Control
Power

Mounting Bracket

Summary of Contents for Shark 100T



































































































































































































































































































































Search results

Summary of Contents for Shark 100T

Reviews:

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 201 / 322

Search results

Summary of Contents for Shark 100T

Reviews: