manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 198 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 198

     

Doc

#    

E154713     

                              

              11-14

11: Using the I/O Options

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

11.8: Optional External I/O Modules

In addition to the Option cards previously explained, the Nexus® 1500+ meter offers 
external I/O modules. The meter acts as a master to any external I/O modules or 
Option cards. All Nexus® external I/O modules have the following components:

•  Female RS485 Side Port: use to connect to another module's male RS485 side port.

•  Male RS485 Side Port: use to connect to the Nexus® 1500+ meter's Port 2 or to 

another module's female RS485 side port. See Figure 11.2 for wiring details.

•  I/O Port: used for functions specific to the type of module. Size and pin configura-

tion vary depending on the type of module.

•  Reset Button: press and hold for three seconds to reset the module's baud rate to 

57600, and its address to 247 for 30 seconds.

•  LEDs: when flashing, the LEDs signal that the module is functioning.

•  Mounting Brackets (MBIO): used to secure one or more modules to a flat surface. 

Comes with 2 DIN rail mounting clips.

Figure 11.2: I/O Module Components

Mounting Brackets (MBIO)

Male RS485 
   Side Port 

Female RS485 
     Side Port 

     I/O Port 

    (Size and Pin 
Configuration Vary) 

 Reset Button 

LEDs 

DIN Rail Mounting Cli

p

s

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments