Electra Meccanica SOLO Emergency Responder'S Manual Download Page 21 | Manualshive

Page: 21 / 46

background image

19

OPENING THE VEHICLE

OPENING THE VEHICLE

Hood

1. Pull the handle (1) located on the side panel under the lower left corner of the dashboard.

2. Lift the secondary catch release lever (2) under the front lip of the cover and raise the hood.

Trunk

Pushing the trunk release button on the dashboard will open the trunk.

Note: The remote transmitter can also be used to open the trunk.

Note: The trunk release button on the dashboard is disabled when the vehicle is locked with the remote transmitter.

1

2

«
...
19
20
21
22
23
...
»

Summary of Contents for SOLO















































Reviews:

No comments

Related manuals for SOLO

Brand: Wahl Pages: 168

HealthyWhite 700 series

Brand: Magnavox Pages: 16

Brand: Olimpia splendid Pages: 8

Brand: Remington Pages: 8

Brand: ALDI Pages: 23

Brand: Westfalia Pages: 23

SNUGASABUG KRH100

Brand: Kambrook Pages: 12

Brand: Amabrush Pages: 34

Brand: O'smiler Pages: 12

Brand: Braun Pages: 22

Oral-B Plak Control D4010

Brand: Braun Pages: 1

Brand: Gaggenau Pages: 48

Silk & Soft LS 5360

Brand: Braun Pages: 73

Brand: Braun Pages: 52

Brand: Thulos Pages: 10

Brand: Grundig Pages: 11

Brand: Grundig Pages: 84

Brand: Grundig Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands