Dedicated gel pad
Instruction Manual
This product is a gel pad specially designed for the ECLEAR LEAN HCT-P01 series
and ECLEAR LEANUP HCT-BTP01 series.
This product is a wearable device that can conduct low-frequency electric current on a human body.
Carefully read the instructions before using the ECLEAR LEAN HCT-P01 series or ECLEAR LEANUP
HCT-BTP01 series to ensure you use the product properly.
Safety Precautions (Important)
To avoid injury and property damage, please comply strictly with the following instructions:
■
The categories of degree of damage or risk caused by failing to follow these instructions are as follows:
Content marked "Prohibited" must be
strictly avoided.
WARNING
indicates cases that have
a "high probability of
death or serious injury".
CAUTION
indicates cases that have
a "probability of injury or
physical damage".
WARNING
Intended for workouts only.
Otherwise, an accident, fault or malfunction may occur.
Do not use the product when the surface of the gel pad is missing or deteriorating.
Otherwise, an accident, fault or malfunction may occur.
Turn off the power before connecting or removing the main unit and gel pads, and before
pasting or removing the gel pads.
Otherwise, an electric shock or malfunction may occur.
Do not use this product on any of the following body parts:
• Chest and other parts near the heart; parts above the neck such as the head and face
• Mucosal surfaces such as wounds, eyes, mouth and genitals
• Parts that have undergone plastic surgery
• Parts where metal, plastic or silica gel has been implanted
• Backbone, spine
• Parts with tattoos
• Abdomen (during menses)
• Parts where necklaces and watches are worn, or puncture sites
CAUTION
Use the gel pad in one place only on the same day. Do not use it for more
than 30 minutes.
It may cause accidents or discomfort.
Ensure that the main unit and gel pad are connected correctly and securely
before use.
Do not leave the gel pads attached on the skin for a long time.
Otherwise, inflammation of the skin may occur.
Do not use this device when placing a gel pad on another pad.
Otherwise, an electric shock or accident may occur.
Do not use or store the product in the locations below.
•
In direct sunlight or near a heating device or other high-temperature units
•
Where there is excessive moisture or vibration. Dusty environments
Otherwise, a fire, electric shock or malfunction may occur.
Do not place loads on the device or use the device in an unsuitable position.
Doing so can cause an electrical malfunction.
Do not touch the special USB cable or gel pads with wet hands.
Otherwise, an electric shock, malfunction or accident may occur.
Keep the device away from children.
Otherwise, accidents may occur. If a child swallows the main unit, consult a
specialist immediately.
Do not use a damp gel pad.
Otherwise, an electric shock or accident may occur.
If you feel any discomfort or skin irritation such as eczema or redness or
itching, stop using the device immediately and consult a specialist.
It may cause accidents or health problems.
Method for Replacing Gel Pads
Do not disassemble, repair or modify the device.
Otherwise, a fire or electric shock may occur.
This product is intended for use by one person only.
It cannot be used by multiple people at a time.
Otherwise, an electric shock or accident may occur.
Do not
disassemble
Package Contents
Twin pad
(consumable)
Core pad
(consumable)
Handling and servicing the product
Content marked "Mandatory" must be strictly
implemented.
■
Handling Gel Pads
• Do not touch the surface of the attachable side of the gel pads.
• Do not bend the gel pads.
• When not in use, paste the gel pads on the two sides of the storage sheet.
• Do not use a damp gel pad.
Before use, completely drain the water and let the adhesive surface dry
naturally.
• The gel pads must be stored in a suitable place and protected from direct
sunlight and high humidity.
■
Maintenance of the Gel Pads (standard of reference:
do maintenance once after every 30 times of use)
Before maintenance, remove the gel pad from the main unit.
Clean the gel pad in any of the following cases:
• The gel pad cannot be securely fixed
• Weak stimulation during use
• Tingling in skin during use
• Dirty gel pad
• The gel pad cannot be fixed to the storage sheet
If the stimulation is still weak or your skin tingles after maintenance, replace the gel pad.
Do not use it on more than two locations at the same time.
It will cause accidents or health problems.
Follow local disposal requirements to dispose of the product.
*This product is not a medical equipment.
This product cannot analyse if you are ill or not.
③
Take the gel pads out of the bag.
(Do not remove the protective film from the gel pad yet.)
②
Remove the main unit from the gel pad.
①
Make sure that the main unit is powered off (LED indicator is off).
④
Connect the gel pad terminal to the main unit until you hear a click.
[When using the core pad]
①
Run a small amount of water on the surface and rub it gently with
your fingertips for several seconds.
※
Do not pour on too much water, otherwise the viscosity will reduce and
the contact surface to be bonded will be damaged.
②
Hold it by the grip and shake it sufficiently to remove
excess water and let it air dry.
※
If not dried thoroughly, adhesion decreases.
※
Do not wipe the adhesive surface with a tissue or cloth.
※
Avoid direct sunlight.
Model number: HCT-BTP01G1
HCT-BTP01G2
HCT-P01 series
HCT-BTP01 series
For use in Hong Kong, Singapore and the Philippines only.
If you made your purchase in another country,
please refer to manual from the relevant country.
www.elecom.co.jp/global/download-list/manual/
※
Replace the twin pads in the same manner.
Model number: HCT-BTP01G1
Model number: HCT-BTP01G2
Contact ELECOM one-stop shop to obtain product description materials (contact
information is listed on the back).
Twin pad (2 pieces)
Storage sheet
Instruction Manual
Core pad (1 piece)
Storage sheet
Instruction Manual
No wet hands